TOC2001NUbb_0620
4/6
TRI
0
2
SYS
sarl
–
300 Rue des Arts et Métiers, 21410 PONT DE PANY
1.1 Use
The modular 4 channels switch receiver
0
2
LINE
10020110
is used to receive radio signals from switch
transmitters or
0
2
LINE
sensors (see compatibility
table §6.1). Designed for switching LED and compact
fluorescent lighting loads, it can also switch resistive
loads (halogen), fluorescent tubes, TBT halogen
lamps with ferromagnetic and electronic transformer,
power contactors or small motors.
The 4 channels switch receiver is equipped with the
« repeater » function as well as the « consumption
indicator » function (see §5.3 and §6.4).
Before use, the transmitters must be assigned to a
receiver. Each sensor or transmitter can control an
unlimited number of receivers.
Note:
Read the user manual carefully before
commissioning.
To
consult
the
consumption
indications, it is recommended to connect the 4
channels switch receiver 10020110 with a suitable
software.
1.2 Guarantee terms
This operating manual is an integral part of the device and our guarantee terms. It must always
be delivered to the user. We reserve the right to modify the technical design of these devices
without warning.
TRI
0
2
SYS
products are manufactured and their quality checked by making
use of the latest technologies and taking into account the applicable national and international
directives. If nevertheless a fault arises,
TRI
0
2
SYS
undertakes to remedy the default as
follows, without prejudicing the rights of the end customer that arise from the sales contract
with his reseller:
If the event of exercising of a legitimate and regular right,
TRI
0
2
SYS
, may at its sole discretion,
rectify the device fault or supply a fault-free device. Any claim beyond this and all claims for
consequential damages are excluded.
A legitimate fault exists if the device cannot be used at the time of delivery to the end customer
because of a design or manufacturing defect or if its practical use is severely limited. The
guarantee is void in cases of natural wear and tear, incorrect use, incorrect connection, where
the device has been repaired or external influence. The guarantee period is 24 months (from
the date of invoicing). French law applies to the regulation of guarantee rights.
WARNING! Risk of electric shocks! (See UTE C18-150) The device contains
live internal components. Risk of wounds or injuries if contact occurs! All work
on the mains supply network and the device must only be carried out by
authorised professional technicians.
•
Before carrying out any work, switch-off and isolate the device.
•
Secure the device to prevent it being switched back on.
•
Check the device is in a zero-volts state.
•
Carefully reclose the casing before reconnecting to mains power.
Observe the following points:
•
The laws, standards and directives in force.
•
The device operating manual and best practice at the time of installation.
•
An operating manual can only give general instructions. They must be interpreted in the
context of a specific installation.
The device is intended solely for use conforming to its purpose. Any repairs or modifications
by the user are forbidden! Do not use with other devices the operation of which could endanger
people, animals or property.
-1-
The output voltage of the 4 channels receiver is the same as the supply voltage.
-2-
Consult us for other types of charges.
-3-
For powers greater than 10W.
-4-
Power consumed without activation of the relays.
Note:
The signal strength between the transmitter and the receiver decreases as the distance
increases. Where there is a line of sight connection, the range is approximately 30m in corridors
and 100 m in large workshops or halls. The range can be increased with an
0
2
LINE
repeater
.
Respect a minimum range of 10 cm between transmitter and receiver.
4.1 Safety instructions
The installation and initial use must only be performed by authorised qualified electricians. The
electrical installation must be placed off-load before connection it to the mains (230V~/50Hz).
Conform to the legislation and standards in force in the country of use.
4.2 Installation
•
This product is designed for indoor use. It is maintenance free.
•
This product is intended for installation only on horizontal DIN rail, in an electrical panel
(mounted on a vertical wall) with compulsory installation of a plastron which will be connected
to the ground of the installation if it is metallic.
•
For compliance with the standard reference, height of the plastron (compared to the above
DIN rail) must not exceed 48 mm with a minimum thickness of 1 mm.
•
NEVER install the receiver in a metal casing or in the immediate vicinity of large metallic
objects.
•
Installation on the ground or close to the ground is not recommended. Thank you to refer to
the installation standards of each country.
•
Protect the supply line with a circuit breaker
6A curve C
adapted to the installation.
Connection principle diagram:
4.3 Description of the connection
- Description of the 4 channels receiver connection:
4.4 Initial use
•
Connect power to the electrical installation after it has been installed.
•
Program the transmitter on the receiver (see § 5).
1. General
2. Safety
3. Technical characteristics
Degree of protection
IP20 with plastron
Range in buildings
Transmission frequency band
868.0 MHZ to 868.6 MHZ
Power supply
110 - 230V
-1-
/ 50 Hz
Ambient temperature
from -10°C to +45°C
Storage temperature
from -20°C to +80°C
Terminal capacity
1x1,5
2
to 2,5
2
max rigid
General characteristics
Output (zero potential)
-2-
4 contacts micro distance (µ) opening
contacts, I
min
=100mA
max µ4x1.5A/4x345VA resistive (cos
φ
=1)
LED: 4x130W
Compact fluorescent: 4x130W
Halogen: 4x345W
Inductive: 4x300W (cos
φ
= 0,4 à 0,6)
Installation altitude
2000m max.
4. Installation and initial use
7mm
WARNI
230V
Installation and operating manual
Modular 4 channels switch receiver for LED
lighting
Ref.
10020110
EN
Ambient humidity
from 0 to 75%hr (without condensation)
Category receiver
2
Power measurement accuracy
2% +/- 1 digits
-3-
Number of modules
1 module of 17.5 mm
Mounting type
DIN rail mounting
Consumed power
< 0.35 W
-4-
Masonry
20m, through 3 walls at most
Reinforced concrete
10m, through 1 wall/ceiling at most
Plasterboard / wood
30m, through 5 walls at most
Schematic diagram of electrical
connection to lighting loads.
They can be replaced by other
types of loads (see table §3).
Transmit power
+10 dBm
