EC 884 PJ
CLOCK PROJECTION
8
8
ACTIVATING/DEACTIVATING THE ALARM
1. Set the ON/OFF switch for alarm 1 (15) or 2 (16) to “ON” to
activate alarm 1 and/or alarm 2 or set to “OFF” to deactivate
alarm 1 and/or alarm 2;
2. If the alarm is activated, alarm 1 will be displayed instead of
the date (5) or alarm 2 instead of the indoor temperature and
humidity (7/8) together with the corresponding symbol
and
(3/4);
3. Alarm sound as below:
0-10sec: BI once/second
10-20sec: BI twice/second
20-30sec: BI four times/second
After 30sec, continuous BI sound
STOPPING THE ALARM/SNOOZE FUNCTION
1. When the alarm is triggered, the alarm symbol
(3) or
(4) begins to flash and an alarm sounds;
2. Press any button (except the LIGHT/SNZ/PROJECTION button
(10)) to stop the alarm. Otherwise, it will stop automatically
after 2 minutes;
3. While the alarm signal is sounding press the LIGHT/SNZ/
PROJECTION button (10) activate the snooze function. The
alarm symbol
/
will begin to flash. The alarm signal
will be stopped for 5 minutes, after which it will sound again.
BACKLIGHT
1
Power from
batteries:
Press the LIGHT/SNZ/PROJECTION button (10) to light up the
display. The display is illuminated for approx. 8 seconds.
2.
Power from
power supply unit:
Press the LIGHT/SNZ/PROJECTION button (10) several times
to change the brightness level (high/low/off, Dimmer function).
Note - Permanent backlight mode
Permanent backlight mode is only possible when plugged into
mains power.
PROJECTION
ACTIVATING/DEACTIVATING
Power from
batteries:
Press the LIGHT/SNZ/PROJECTION button (10) to project the display
onto the wall or ceiling for 8 seconds.
Power from
power supply unit:
1. Press and hold the LIGHT/SNZ/PROJECTION button (10) for
approximately 3 seconds to activate sustained projection.
2. Press and hold the LIGHT/SNZ/PROJECTION button (10) for
approximately 3 seconds to deactivate sustained projection.
PROJECTION SETTING
1. Turn the projection arm (9) forward/back to project the display
onto the desired wall/ceiling;
2. Press the ROTATE button (17) again to rotate the projection by
0°, 90°, 180° or 360°.
CHARGING FUNCTION
1. Connect your terminal device to a USB charging socket (20)
on the alarm clock using a suitable USB cable;
2. The charging progress is displayed on your terminal device;
3. Disconnect the terminal device from the USB charging socket
if you want to interrupt charging or if the terminal device is fully
charged.
Note - Connecting terminal devices
• The charging function is only possible when plugged into mains
power.
• Before connecting a terminal device, check whether the power
output of the charger can supply sufficient power for the device.
• Please refer to the instructions in the operating manual of your
terminal device.
SPECIFICATION
Power Supply: ........................... 5V
1A
Battery: .................................... 2x 1,5V
(“AAA”size,
Not included)
USB Output: ............................. 5V
1A
Measuring range temperature: ... -9°C-+50°C /14°F-+122°F
Measuring range humidity: ........ 20%-95%
Size: ........................................151x 94x 42mm
Precautions for correct disposal of the product
The symbol shown on the equipment indicates that waste must be
disposed of in “separate collection” and so the product must not
be disposed of together with urban waste.
The user must take the product to special “separate waste collection
centres” provided by local government, or deliver it to the retailer
against the purchase of a new product.
Separate collection of waste and subsequent treatment, recycling
and disposal operations promotes the production of equipment with
recycled materials and limits negative effects on the environment
and on health caused by improper handling of waste.
Illegal disposal of the product leads to the enforcement of admi-
nistrative penalties.
ENGLISH