Traxxas TRX 2.5R Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 40

background image

TRX 2.5R • 25

2.

If necessary, remove the air filter to gain access to the idle adjustment screw.

3.

Turn the screw counterclockwise to reduce the idle speed, or clockwise to increase it.
The idle speed should be set as low as possible while still maintaining reliable
running characteristics.

4.

Reset the throttle trim on the transmitter to its original position.

Fine-Tuning the Carburetor

After fine-tuning your TRX 2.5R Racing Engine at the end of the break-in procedure, no major
adjustments to the fuel mixture are usually necessary. Make note of the temperature, humidity,
and barometric pressure at the time you finished fine tuning your carburetor. Current weather
conditions can be found online from national websites, local TV news websites, and television.
This information will be considered your baseline setting. You may need to adjust your
carburetor needles to compensate for changes in temperature and barometric pressure (air
density) from day to day. Generally, you’ll need to richen the fuel mixture when the weather is
colder than your baseline temperature and the air density is higher. Lean the fuel mixture when
weather is warmer than your baseline temperature and the air density is lower. The chart below
provides general guidelines on how weather conditions affect air density when they move
higher or lower than your baseline setting (see page 14 for detailed info on how air density
affects mixture settings).

If the...

Humidity

Pressure (barometer)

Temperature

Altitude

Nitro %

is..

Lower
Higher
Lower
Higher
Lower
Higher
Lower
Higher
Lower
Higher

then the

air density is...

Slightly more dense
Slightly less dense

Less dense
More dense
More dense
Less dense
More dense
Less dense

adjust (correct)

the fuel mixture to be...

Slightly richer
Slightly leaner

Leaner
Richer
Richer
Leaner
Richer
Leaner
Leaner
Richer

TUNING THE TRX 2.5R

«
...
23
24
25
26
27
...
»

Содержание TRX 2.5R









































Отзывы:

Нет отзывов

Похожие инструкции для TRX 2.5R

Бренд: Westerbeke Страницы: 60

Бренд: Ofna Racing Страницы: 2

Бренд: Briggs & Stratton Страницы: 26

Бренд: TCF Страницы: 16

Бренд: Nederman Страницы: 44

Бренд: O.S. engine Страницы: 13

MAX-15CV Series

Бренд: O.S. engine Страницы: 30

Бренд: Lycoming Страницы: 84

Бренд: CAME Страницы: 64

Бренд: Yanmar Страницы: 164

Бренд: Honda Страницы: 7

Бренд: O.S. Speed Страницы: 4

Бренд: Barrus Страницы: 59

Бренд: Briggs & Stratton Страницы: 13

Бренд: A-iPower Страницы: 52

Бренд: Grundfos Страницы: 76

Бренд: Marine Power Страницы: 45

Бренд: Briggs & Stratton Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды