14 • TQ
i
RADIO SYSTEM
Press MENU
to move through options.
Press SET
to select an option.
Press MENU
to move through options.
Press SET
to select an option.
Press SET
to select an option.
Enter Programming
Press and hold
MENU for 3 seconds
Steering Sensitivity (Expo)
One Blink Red
1
Electric
One Blink Red
1
Unlock
One Blink Red
1
Confirm Deletion
One Blink Red
1
Multi-Function Knob
One Blink Green
1
Channel Setup
Two Blinks Green
2
Mode Selection
Three Blinks Green
3
Traxxas-Link
Four Blinks Green
4
Steering (Channel 1)
One Blink Green
1
Model Locking
One Blink Green
1
Shift (Channel 3)*
Three Blinks Green
3
Front T-Lock (Channel 4)*
Four Blinks Green
4
Rear T-Lock (Channel 5)*
Five Blinks Green
5
Throttle (Channel 2)
Two Blinks Green
2
Delete Model
Two Blinks Green
2
Throttle Sensitivity (Expo)
Two Blinks Red
2
Nitro
Two Blinks Red
2
Lock
Two Blinks Red
2
Steering % (Dual Rate)
Three Blinks Red
3
Unlock All
Three Blinks Red
3
Braking %
Four Blinks Red
4
Throttle Trim
Five Blinks Red
5
Knob Disabled
Six Blinks Red
6
Press
MENU
Press
MENU
Press
MENU
Press
MENU
Press
MENU
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Servo Reversing
One Blink Red
1
Press SET to reverse
servo direction.
Servo Reversing
One Blink Red
1
Press SET to reverse
servo direction.
Servo Reversing
One Blink Red
1
Press SET to reverse
servo direction.
Reset End Points
Four Blinks Red
4
Press SET to restore
factory default endpoints.
Reset End Points
Four Blinks Red
4
Press SET to restore
factory default endpoints.
Sub Trim
Two Blinks Red
2
Use knob to adjust
sub-trim. Press SET to save.
Sub Trim
Two Blinks Red
2
Use knob to adjust
sub-trim. Press SET to save.
End Points
Three Blinks Red
3
Use steering wheel to
adjust. Turn right to desired
end point, press set to save.
Turn left to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
The menu tree below shows how to navigate through the
TQi transmitter’s various settings and functions. Press and
hold MENU to enter the menu tree, and use the following
commands to navigate through the menu and select options.
MENU:
When you enter a menu, you always start at the top.
Press MENU to move down the menu tree. When you
reach the bottom of the tree, pressing MENU again will
return you to the top.
SET:
Press SET to move across the menu tree and select
options. When an option is committed to the transmitter’s
memory, the status LED will rapidly blink green.
BACK:
Press both MENU and SET to go back one level in the
menu tree.
EXIT:
Press and hold MENU to exit programming. Your
selected options will be saved.
ECHO:
Press and hold SET to activate the “echo” function. Echo
will “play back” your current position on the Menu Tree,
should you lose your place. For example: If your current
position is Steering Channel End Points, holding SET will
cause the LED to blink green twice, green once, and then
red three times. Echo will not alter your adjustments or
change your position in the programming sequence.
MENU TREE
Below is an example of how to access a function in the menu
tree. In the example, the user is setting the Multi-Function knob
to be a steering Dual Rate control.
To set the Multi-Function knob to control STEERING DUAL RATE (%):
1. Switch the transmitter on
2. Press and hold MENU until the green LED lights. It will blink in single intervals.
3. Press SET. The red LED will blink in single intervals to indicate Steering Dual
Rate has been selected.
4. Press MENU twice. The red LED will blink three times repeatedly to indicate
Steering Percentage has been selected.
5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.
6. Press and hold MENU to return to driving mode.
Note: The transmitter is “live” during programming
so you can test the settings real time without having
to exit the menu tree.
End Points
Three Blinks Red
3
Use trigger to adjust. Pull
back to desired end point,
press set to save. Push
forward to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
Press
SET
* 4-Channel transmitter only
Restoring Factory Defaults:
When programming your transmitter, you may feel the need
to start over with a clean slate. See
Selecting Your Model Profile
(Resetting to Defaults)
on page 6 for instructions.
Содержание TQi 6507
Страница 1: ...owners manual MODELS 6507 6508 6509...
