background image

 SUMMIT

This model is not intended 
for use by children under 
14 years of age without the 
supervision of a responsible 
and knowledgeable adult.

All instructions and 
precautions outlined in this 
manual should be strictly 
followed to ensure safe 
operation of your model.

Previous experience with 
radio controlled models 
is recommended. Models 
require a higher level of 
setup, maintenance, or 
support equipment.

Skill Level = Myriad Semi Bold

SAFETY PRECAUTIONS

• Don’t Get Burned: The ESC and motor can become extremely hot during 

use, so be careful not to touch them until they cool. Supply adequate 
airlow for cooling.

• Use the Factory-Installed Stock Connectors: Do not change the battery and 

motor connectors. Improper wiring can cause ire or damage to the ESC. 
Please note that modiied speed controls can be subject to a rewiring fee 
when returned for service.

• No Reverse Voltage: The ESC is not protected against reverse polarity 

voltage. 

• Do Not Let the Transistor Tabs Touch: Never allow the three separate 

transistor banks to touch each other or any exposed metal. This will create a 
short circuit and damage the ESC.

• No Schottky Diodes: External Schottky diodes are not compatible with 

reversing speed controls. Using a Schottky diode with your Traxxas speed 
control will damage the ESC and void the 30-day warranty.

• Always adhere to the minimum 

and maximum limitations of the 
speed control as stated in the 
speciications on page 17. If your 
ESC operates on two batteries, 
do not mix battery types and 
capacities. Use the same voltage 
and capacity for both batteries. 
Using mismatched battery packs 
could damage the batteries and 
electronic speed control.

LiPo Batteries

Lithium Polymer (LiPo) batteries are becoming popular for use in R/C 
models due to their compact size, high energy density, and high-current 
output. However, these types of batteries require special care and handling 
procedures for long life and safe operation. 

Warning: 

LiPo batteries are 

intended only for advanced users that are educated on the risks associated 
with LiPo battery use. 

Traxxas does not recommend that anyone under the 

age of 14 use or handle LiPo battery packs without the supervision of a 
knowledgeable and responsible adult. 

Your model is able to use LiPo batteries. LiPo batteries have a minimum safe 
discharge voltage threshold that should not be exceeded. The electronic 
speed control is equipped with built-in Low-Voltage Detection, which 
alerts the driver when LiPo batteries have reached their minimum voltage 
(discharge) threshold.

 It is the driver’s responsibility to stop immediately to 

prevent the battery pack from being discharged below its safe minimum 
threshold.

Low-Voltage Detection on the speed control is just one part of a 
comprehensive plan for safe LiPo battery use.

 It is critical for you, the user, 

to follow all other instructions supplied by the battery manufacturer and 
the charger manufacturer for proper charging, use, and storage of LiPo 
batteries. Make sure you understand how to use your LiPo batteries. 

Be 

aware that Traxxas shall not be liable for any special, indirect, incidental, 
or consequential damages arising out of the installation and/or use of 
LiPo batteries in Traxxas models. If you have questions about LiPo battery 
usage, please consult with your local hobby dealer or contact the battery 
manufacturer. As a reminder, all batteries should be recycled at the end of 
their useful life.

TERMS OF USE

 - The buyer assumes all risk associated with using this 

product. Traxxas, its afiliates, manufacturers, distributors, and retail partners 
cannot control the use, application, charging, or installation of this product 
and shall not be held responsible for any accident, injury to persons, or 
damage to property resulting from the use of this product. 

After reading all, if you do not agree with these terms and conditions and 
are not prepared to accept complete liability for the use of this product, 
return this product immediately in new/unused condition to your place of 
purchase. 

Your retailer absolutely cannot accept product for return or 

exchange if it has been used in any way.

If you have any questions, call Traxxas Customer Support at 1-888-TRAXXAS  
(1-888-872-9927) Outside the US +1-972-265-8000 or e-mail support@
traxxas.com.

1500

3600

Do not mix battery 
capacities. Use two 

batteries with the  

same capacity. 

Do not use a 6-cell 7.2V 
battery in combination 

with a 7-cell battery 

8.4V pack.

WARNING!   CAUTION!   DANGER! 

FIRE HAZARD!

 

Charging and discharging batteries has the potential for 

ire, explosion, serious injury, and property damage if not performed per the 
instructions. In addition, Lithium Polymer (LiPo) batteries pose a SEVERE risk of 
ire if not properly handled per the instructions. Before use, read and follow all 

manufacturer’s instructions, warnings, and precautions. Never allow children under 14 years old 
to charge or use LiPo batteries without the supervision of a responsible, knowledgeable adult.

• While charging or discharging, ALWAYS place the battery (all types of batteries) in a ire 

retardant/ire proof container and on a non-lammable surface such as concrete.

• ALWAYS charge batteries in a well-ventilated area.

• REMOVE lammable items and combustible materials from the charging area.

• ONLY use a Lithium Polymer (LiPo) balance charger with a balance adapter to charge LiPo 

batteries.

• If any battery or cell is damaged in any way, DO NOT charge, discharge, or use the battery.

• BEFORE you charge, ALWAYS conirm that the charger settings exactly match the battery 

type (chemistry), speciication, and coniguration to be charged.

• DO NOT exceed the maximum manufacturer recommended charge rate.

• DO NOT disassemble, crush, short circuit, or expose the batteries to lame or other source  

of ignition.

• NEVER leave batteries unattended while charging.

Содержание Summit 1:10 TRA5607L





































Отзывы: