background image

4 • REVO 3.3

This model is not intended 
for use by children (minors)
under 16 years of age 
without the supervision 
of a responsible and 
knowledgeable adult.

All instructions and 
precautions outlined in this 
manual should be strictly 
followed to ensure safe 
operation of your model.

SAFETY PRECAUTIONS

Model requires detailed 
setup, and/or maintenance 
procedures with required 
support equipment. 
Previous experience with 
radio controlled models is 
mandatory. This model is 
capable of very high speeds 
and requires a high level of 
skilled driving control.

Skill Level = Myriad Semi Bold

1 2 3 3+ 4 5

bluehighway font

For Expert Drivers

Choose the Model That is Right For You.

For individual Models

No previous experience with radio controlled models is required.

Models require a minimum of setup, maintenance, or support equipment. 

Previous experience with radio controlled models is mandatory. These 

models are capable of high speeds, requiring experienced driving control. 

Models require detailed setup, and/or maintenance procedures with required 

support equipment. 
Previous experience with radio controlled models is mandatory. 

These models are capable of very high speeds and require an even higher 

level of skilled driving control. Models require detailed setup, and/or mainte-

nance procedures with required support equipment. 

For Expert Drivers Only.

 This product is capable of extreme speed 

and acceleration! It carries our highest skill level rating and is intended 

for expert drivers only. Experience with nitro-powered radio controlled 

models is required!

Previous experience with radio controlled models is recommended.

Models require a higher level of setup, maintenance, or support equipment. 

No previous experience with radio controlled models is required.

Model requires a minimum of setup, maintenance, or support equipment. 

Previous experience with radio controlled models is mandatory. This model is 

capable of high speeds, requiring experienced driving control. Model requires 

detailed setup, and/or maintenance procedures with required support 

equipment. 

Previous experience with radio controlled models is mandatory. This model is 

capable of very high speeds and requires an even higher level of skilled driving 

control. Model requires detailed setup, and/or maintenance procedures with 

required support equipment. 

For Expert Drivers Only.

 This product is capable of extreme speed 

and acceleration! It carries our highest skill level rating and is intended 

for expert drivers only. Experience with nitro-powered radio controlled 

models is required!

 Previous experience with radio controlled models is recommended.

Model requires a higher level of setup, maintenance, or support equipment.

BELOW TEXT HAS BEEN UPDATED on 3-14-07
Kent wants maintenance text to be at the END of the paragraph.-- KB

All of us at Traxxas want you to safely enjoy your new Revo. Operate 
your Revo sensibly and with care, and it will be exciting, safe, and fun 
for you and those around you. Failure to operate your Revo in a safe and 
responsible manner may result in property damage and serious injury. 
The precautions outlined in this manual should be strictly followed to 
help ensure safe operation. You alone must see that the instructions are 
followed and the precautions are adhered to. 

IMPORTANT POINTS TO REMEMBER

•  Revo is very fast! The Revo is intended for experienced users with a high 

level of skill. The TRX 3.3 Racing Engine is extremely powerful and may 
require skilled driving to maintain control. Children under 16 years of 
age and inexperienced drivers should not operate the Revo without the 
supervision of a responsible and knowledgeable (experienced) adult.

• 

Model engine fuel is dangerous and highly poisonous.

 Always follow 

all directions and precautions printed on the fuel container. Model 
engine fuel is poisonous to humans and animals. Drinking the fuel can 
cause blindness and death. Handle with care and respect.

•  Model engine fuel, especially when in a fuel dispensing bottle, may look 

like a cool drink to a child. 

Keep all fuel out of the reach of children at 

all times. Do not place fuel containers on the ground where children 
can reach them while you are driving.

•  Model engine fuel is flammable. Never allow smoking, sparks,  

heat or flame in the presence of fuel or fuel vapors.  

•  The engine, brakes, and exhaust system may become extremely hot 

during use. Be careful not to touch the parts, especially when refueling 
or stopping the engine.

•  Prolonged exposure to the engine exhaust can be harmful. Avoid 

breathing the engine exhaust. Always run your Revo outdoors,  
in a well-ventilated area. Never run the engine indoors. 

•  Do not operate your Revo at night, or anytime your line of sight to the 

model may be obstructed or impaired in any way.

•  Never operate your Revo in crowds of people or busy pedestrian 

areas. Revo is very fast  and could cause injury to those unaware of 
its presence. Keep small children at a safe distance away from the 
operating area.

•  Because Revo is controlled by radio, it is subject to radio interference 

from many sources beyond your control. Since radio interference can 
cause momentary loss of control, always allow a safety margin in all 
directions around your model to prevent collisions. 

•  Do not kink the antenna wire. Kinks in the antenna wire will reduce range.
•  The engine can be loud. If the noise makes you uncomfortable, wear ear 

protection. Be considerate of your neighbors by not running your model 
early in the morning or late in the evening.

•  Do not cut the antenna “stinger” or any other part of the antenna wire. 

Cutting the antenna will reduce range.

•  Extend the antenna as far as possible for maximum range. It is not 

necessary to extend the antenna wire out of the body, but wrapping or 
coiling the antenna wire should be avoided. 

•  Do not allow the antenna wire to extend outside the body without the 

protection of an antenna tube, or the antenna wire may incur crash 
damage that could reduce range.

• 

Most importantly, use good common sense at all times.

BATTERIES AND BATTERY CHARGING

Your model uses rechargeable batteries that must be handled with care for 
safety and long battery life. Make sure to read and follow all instructions and 
precautions that were provided with the battery packs and your charger. It 
is your responsibility to charge and care for the battery packs properly. In 
addition to your battery and charger instructions, here are some more tips 
to keep in mind.
•  Use the supplied chargers to charge the included batteries. See “Charging 

the Receiver Battery” on page 10 and “Charging the  
EZ-Start Battery” 
on page 23. 

•  Never leave batteries to charge unattended.
•  Allow the battery pack to cool off before charging.
•  Do not use battery packs that have been damaged in any way.
•  Do not use battery packs that have damaged wiring, exposed wiring, or a 

damaged connector. 

•  Children should have responsible adult supervision when charging and 

handling batteries.

•  Only use approved chargers for Nickel Metal Hydride (NiMH) battery 

packs (such as the Traxxas EZ-Peak Plus, part #2933). Do not exceed the 
maximum charge rate of 1 amp.

•  Do not short-circuit the battery pack. This may cause burns and severe 

damage to the battery pack

•  Do not burn or puncture the batteries. Toxic materials could be released. 

If eye or skin contact occurs, flush with water.

•  Store the battery pack in a dry location, away from heat sources  

and direct sunlight.

•  NiMH batteries must be recycled or disposed of properly.  

Recycling Your Traxxas Power Cell NiMH Battery

Traxxas strongly encourages you to recycle your Power Cell battery  
when it has reached the end of its useful life. 

Do not throw your  

battery in the trash.

 All Power Cell battery packs display the RBRC 

(Rechargeable Battery Recycling Corporation) icon, indicating they are 
recyclable. To find a recycling center near you, ask your local hobby dealer 
or visit www.call2recycle.org.

1

Содержание Revo 3.3 53097

















































Отзывы: