background image

2 • 1/16 SLASH 4WD

3

 

BEFORE YOU 
PROCEED

3

 SAFETY 

PRECAUTIONS

5

 

TOOLS, SUPPLIES, 
AND REQUIRED 
EQUIPMENT

6

 

ANATOMY OF THE 
1/16 SLASH 4WD

7

 

QUICK START: 
GETTING UP  
TO SPEED

8

 

THE TRAXXAS  
TQ 2.4GHz RADIO 
SYSTEM

16

  ADJUSTING THE 

ELECTRONIC SPEED 
CONTROL

18

  DRIVING YOUR MODEL

21

 TUNING 

ADJUSTMENTS

25

 MAINTAINING 

 

YOUR MODEL

INTRODUCTION

Thank you for purchasing a Traxxas 1/16 scale model. Your new 
model combines proven Traxxas innovations including F1-
inspired, rocker-actuated suspension, waterproof electronics, 
and a monocoque-style chassis for outstanding handling and 
incredible speed and power. Your Traxxas model is designed for 
high-performance driving, with balanced weight distribution, 
lightweight and high-strength materials, and the precise 
engineering that is the hallmark of all Traxxas vehicles.
 
This manual contains the instructions you will need to operate and 
maintain your model so that you can enjoy it for years to come. 
We want you to feel confident that you own one of the best-
performing models in the market and that it is backed by a team 
of professionals who aim to provide the highest level of factory 
support possible. Traxxas models are about experiencing total 
performance and satisfaction, not just with your model, but also 
with the company that stands behind it. 

We know you’re excited about getting your new model on the 
road or trail, but it’s very important that you take some time to 
read through the Owner’s Manual. This manual contains all the 
necessary setup and operating procedures that allow you to unlock 
the performance and potential that Traxxas engineers designed 
into your model. 

Even if you are an experienced R/C enthusiast, 

it’s important to read and follow the procedures in this manual.

Thank you again for going with Traxxas. We work hard every day to 
assure you the highest level of customer satisfaction possible. We 
truly want you to enjoy your new model!

Traxxas Support

Traxxas support is with you every step of the 
way. Refer to the next page to find out how to 
contact us and what your support options are.

Quick Start

This manual is designed with a Quick 
Start path that outlines the necessary 
procedures to get your model up 
and running in the shortest time possible. If you are an 
experienced R/C enthusiast, you will find it helpful and fast. 
Be sure and read through the rest of the manual to learn 
about important safety, maintenance, and adjustment 
procedures. Turn to page 7 to begin.  

FCC Compliance

This device contains a module that complies with the limits for a Class B digital device as described in part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The limits for a Class B digital device are designed to provide reasonable protection against harmful interference in residential settings. This product generates, uses and can radiate radio frequency energy, and, if 
not operated in accordance with the instructions, may cause harmful interference to radio communications. The user is cautioned that changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.

Canada, Industry Canada (IC)

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: This 
device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency (RF) Exposure Information

The radiated output power of the Traxxas LP Device is below the Industry Canada (IC) radio frequency exposure limits. The antenna for this transmitter must not be co-located with any other transmitters except in 
accordance with FCC and Industry Canada multi-transmitter procedures. Co-location means having a separation distance of less than 20 cm between transmitting antennas.

REGISTERING YOUR MODEL

In order to serve you better as our customer, please  
register your product within 10 days of your purchase  
online at Traxxas.com/register.

T r a x x a s . c o m / r e g i s t e r

Содержание 1/16 SLASH 4x4 70054



























Отзывы: