background image

 

Gas/Pellet Remote Thermostat 

SKU 99300689 

 

Page 7 of 8 

3/7/12  -  17601682 

© Travis Industries, Inc.  

Auto Mode 

Auto mode works 
like a thermostat, 
turning the heater 
on and off to meet 
the desired 
temperature.

 

MA

NU

AL

ON/

OFF

AUTO ON/

OFF

TIMER

CLOCK

THERMOSTAT MODE:
Use this key to toggle the 
thermostat mode.  The 
display will indicate 
“AUTO” when in 
thermostat mode.

TO ADJUST TARGET TEMPERATURE:
Use the arrow keys to adjust the target 
temperature to the desired level.

The heater will turn on and off to keep the 
room temperature near the target 
temperature.

IMPORTANT NOTES:
-- The thermostat has a delay to prevent the heater 
from turning on and off repeatedly.  As a result, the 
target temperature may be slightly higher (2° or 3°) 
than the room temperature yet the heater does not 
turn on – do not adjust the target temperature – the 
heater will turn on in a few minutes.

HINT:
If your heater turns on 
and off frequently, adjust 
the flame height down 
slightly for a more 
consistent heat output.

AUTO

°F

AM

SET TEMP

 

 
 

Timed Mode 

Timed mode allows 
you to turn the 
heater on for a pre-
set period of time. 

 

MA

NU

AL

ON/

OFF

AUTO ON/

OFF

TIMER

CLOCK

OFF

°F

SET TEMP

The heater will turn on and 
stay running for the number of 
minutes displayed.

TIMED OPERATION:

a) 

b)

c)

Use the arrow keys to adjust the 

target temperature to 90°.

Press the “TIMER” button - the 

“ - - -” will start to flash.

Use the arrow keys to set the 

number of minutes you would like 

the heater to stay on.

NOTE:
If the room exceeds 90°, the 
heater will shut off.

TIMER

 

Содержание SKU 99300689









Отзывы: