Travis Industries LOPI Liberty Скачать руководство пользователя

Страница: 28 / 38

Maintaining Your Appliance

100-01164

4041115

Firebox Parts

ID #

Description

Qty

Part #

ID #

Description

Qty

Part #

Air Tubes & Sleeve

98900210

Air Tube Roll Pins

98900357

3Air Tube Retainer Sleeve

3100-11001

Baffle Support, Front "Y"

99900277

Baffle Support, Rear "T"

99900278

Damper Plate

98900320

Damper Slider

98900340

Damper Yoke

98900326

Damper Extension Rod with
Pull Ring

98900333

Brick - 9" x 4.5" un-cut

175-00001 (1)
98900102 (9)

Brick, Cut - 8.25" x 4.5"

251-00010

Brick, Cut – 6.25” x 4.5”

251-00011

Floor and Side Firebrick Removal & Replacement

Do not pry firebrick - they chip and crack easily.

Remove the floor firebricks first. The side firebrick

are removed later because they are pinned in place by the floor firebrick. Clean the firebox prior to
replacing the firebrick.

Содержание LOPI Liberty







































Результаты поиска

Содержание LOPI Liberty

Отзывы:

Похожие инструкции для LOPI Liberty

Бренды по названию

Популярные бренды

Travis Industries LOPI Liberty, Руководство пользователя

Результаты поиска

Содержание LOPI Liberty

Отзывы:

Похожие инструкции для LOPI Liberty

Бренды по названию

Популярные бренды