Travis Industries LOPI Liberty Скачать руководство пользователя

Страница: 36 / 38

Optional Equipment

100-01164

4041115

Rear Blower Installation (Part # 99000138)

The rear blower improves heat transfer by pushing heated air through the convection channel. Operating
instructions are described in the section "Blower Operation".

The stove should be in place with the legs installed prior to installing the rear blower.

Follow the directions below to install the blower. Use the

Use the wire clip to insure the wires from the thermodisk are held in place away from the firebox (this
prevents damage to the wires).

Slide the
thermodisk
assembly into
the space
between the
stove and rear
heat shield.

Run both of the
wires from the
thermodisk down
behind the stove
and through the
eye of the wire clip.

Wire Clip

Thermodisk

This portion
hooks on the
top edge of the
rear heat shield.

The two yellow wires
attach to the thermodisk.

Three holes for
attaching the
blower box to the
back of the stove

Power Cord
(exits from back
of blower box)

Blower Box

FRONT

Wire Clip

This portion of the wire
clips slides over the
rear heat shield

The wires pass through the eye of the wire clip.

Содержание LOPI Liberty







































Результаты поиска

Содержание LOPI Liberty

Отзывы:

Похожие инструкции для LOPI Liberty

Бренды по названию

Популярные бренды

Travis Industries LOPI Liberty, Руководство пользователя

Результаты поиска

Содержание LOPI Liberty

Отзывы:

Похожие инструкции для LOPI Liberty

Бренды по названию

Популярные бренды