Travis Industries Lopi GreenField GS Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 64

background image

Featuring the

Burner

• Direct Vent Freestanding Stove

• Natural Gas or Propane

• Vent Horizontally or Vertically

• Standard Residential

• Mobile Home Approved

Tested and Listed by

ANSI Z21.88 CSA 2.33

WARNING

:

If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of
life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any phone in your building.
•  Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an

aftermarket permanently located,
manufactured home (USA only) or mobile
home, where not prohibited by local
codes.

This appliance is only for use with the
type(s) of gas indicated on the rating plate.
A conversion kit is supplied with the
appliance.

GreenField

Owner’s Manual

INSTALLER

:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

©

Copyright 2010, T.I. $10.00 100-01255_000 4101028

www.travisproducts.com

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

1
2
3
...
»

Содержание Lopi GreenField GS

































































Отзывы:

Нет отзывов

Похожие инструкции для Lopi GreenField GS

Бренд: KASTOR Страницы: 69

Бренд: Napoleon Страницы: 36

Бренд: U.S. Stove Страницы: 35

Бренд: Vermont Castings Страницы: 9

Бренд: Vermont Castings Страницы: 28

Бренд: Coleman Страницы: 24

Бренд: Coleman Страницы: 32

Бренд: St. Croix Страницы: 54

Бренд: Residential Retreat Страницы: 64

EasyFuel II EF 3277

Бренд: Primus Страницы: 4

Бренд: Primus Страницы: 2

Doris Bianco Infinity

Бренд: Nordica Страницы: 60

TERMOPALEX 78 FAST

Бренд: Palazzetti Страницы: 20

GREENLINE WT NM 12-25

Бренд: NARVI Страницы: 44

Бренд: Cadel Страницы: 40

Бренд: Ravelli Страницы: 174

Бренд: Ravelli Страницы: 12

Бренд: Bullerjan Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды