Travis Industries Lopi GreenField GS Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

background image

24

Installation

(for qualified installers only)

© Travis Industries

4101028

100-01255_000

Steps for Finalizing the Installation

1. Remove the glass (see page 26).

NOTE:

If using propane (LP) convert the appliance prior to installing the logs.

2. We recommend you purge the gas line at this time (with the glass removed). This allows gas to be detected

once it enters the firebox, ensuring gas does not build up.

3. Make sure the accent light works correctly.

NOTE

: Take care to not touch the bulb with your fingers – use a cloth or paper towel).

4. Install the four AA batteries (included in the owner’s pack) into battery holder (see the illustration below). The AA

batteries act as a power backup in case the household (AC) power goes out. Install the 9v battery (included in
the owner’s pack) into control panel light assembly (see the illustration below). The battery holder is held in place
with Velcro and may be removed for easier access.

AA Battery

AA Battery

Swing the control
cover down to
access the batteries.

AA
Battery
Holder

AA Battery Tray

AA Battery

AA Battery

9v

Battery

Battery Holder for
Control Panel Lights

5. Install the logs (see page 28).

6. Replace the glass.

7. Start the heater.

8. Leak test all gas joints.

«
...
22
23
24
25
26
...
»

Содержание Lopi GreenField GS

































































Отзывы:

Нет отзывов

Похожие инструкции для Lopi GreenField GS

Бренд: HAAS + SOHN Страницы: 23

Бренд: Cadel Страницы: 94

Бренд: Zibro Страницы: 137

Бренд: radiance Страницы: 13

Бренд: RAIS Страницы: 56

Бренд: Quadra-Fire Страницы: 36

BEA majolica oven

Бренд: Cola Страницы: 12

Бренд: Aarrow Страницы: 28

Бренд: Pelpro Страницы: 32

Бренд: Morso Страницы: 12

2B Classic 2020

Бренд: Morsø Страницы: 631

Бренд: Cadel Страницы: 32

Бренд: Cadel Страницы: 36

ACCENT AIRTIGHT

Бренд: Cadel Страницы: 40

Бренд: Cadel Страницы: 72

Бренд: Cadel Страницы: 72

Бренд: HAAS + SOHN Страницы: 18

Бренд: Haas+Sohn Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды