Travis Industries Lopi GreenField GS Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 64

background image

Operation

37

© Travis Industries

4101028

100-01255_000

Normal Operating Sounds

Gas Control Valve

As the gas control valve is turned
on and off you will hear a dull
clicking sound. This is the valve
opening up and shutting down.

Blower Snap Disk

This part can produce a clicking
sound as it turns the blower on
and off.

The appliance may creak with change of
temperature -- THIS IS NORMAL.

Pilot Assembly

The pilot flame will make a clicking
sound when starting up. If left on, it
will make a slight whisper sound.

Blower

This heater has an optional blower to push
heated air into the room. You will hear the
sound of air movement that increases as
the speed is increased.

Extinction Pops

It is not unusual, especially on Propane
(LP) appliances, to experience a "pop"
when the burner is shut off.

GreenSmart Receiver

The optional GreenSmart receiver will
beep when receiving commands from the
GreenSmart remote.

AC Adapter

This device makes a light hum that is
audible in close proximity.

Normal Operating Odors

This appliance has several areas that reach high temperatures. Dust or other particles on these areas
may burn and create a burnt-paper smell. This is normal during startup. You may notice the smell is
more acute if the appliance was left idle for a long period.

«
...
35
36
37
38
39
...
»

Содержание Lopi GreenField GS

































































Отзывы:

Нет отзывов

Похожие инструкции для Lopi GreenField GS

Бренд: Harman Home Heating Страницы: 40

Бренд: RAIS Страницы: 56

Бренд: RAIS Страницы: 81

Бренд: Zibro Страницы: 120

Бренд: United States Stove Страницы: 43

Бренд: Radijator Страницы: 86

Бренд: Drolet Страницы: 36

ECOFIRE MEGHAN Series

Бренд: Palazzetti Страницы: 28

Бренд: Empire Страницы: 56

ARDENNES 134 13 15

Бренд: FRANCO BELGE Страницы: 14

Бренд: Daytona Страницы: 4

Бренд: DeLonghi Страницы: 7

Бренд: Costway Страницы: 5

Бренд: GARDECO Страницы: 12

Бренд: PASIAN Страницы: 74

Бренд: Palazzetti Страницы: 12

Бренд: Ariterm Страницы: 16

ECOFIRE BEATRICE

Бренд: Palazzetti Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды