Travis Industries Lopi GreenField GS Скачать руководство пользователя страница 58

Страница: 58 / 64

Optional

Equipment

(for qualified installers only)

4101028

100-01255_000

Use the included torx wrench to remove the stock regulator (see Figure 14). The old regulator may
be discarded.

Figure 14

10 The stepper motor (adjustable regulator) has an installation sheet included with it – make sure to

follow all of the directions. Place the stepper motor on the gas control valve (see Figure 15) –

MAKE

SURE IT IS CORRECTLY ORIENTED

. Secure using the screws included with the motor (see Figure

16) – tighten to 25 Lb-inches. Leak test this area after installation to verify proper installation.

Figure 15

Figure 16

11 Place the GreenSmart wiring harness in front of the stove, noting the position of each connector (see

.Figure 17).

Figure 17

Содержание Lopi GreenField GS

































































Результаты поиска

Содержание Lopi GreenField GS

Отзывы:

Похожие инструкции для Lopi GreenField GS

Бренды по названию

Популярные бренды

Travis Industries Lopi GreenField GS, Руководство пользователя

Результаты поиска

Содержание Lopi GreenField GS

Отзывы:

Похожие инструкции для Lopi GreenField GS

Бренды по названию

Популярные бренды