Travis Industries 430 Mod-Fyre GSR2 Скачать руководство пользователя страница 50

Страница: 50 / 66

Optional Equipment

(for qualified installers only)

5/20/2021 - 1558

430 MF GSR2

8. Install the LP pilot orifice following the directions below.

(a) Use a 7/16” open-end wrench to remove the pilot hood.

(b) Remove and discard the Natural Gas (NG) orifice. Place the LP orifice in the pilot assembly then replace the

pilot hood, tightening the pilot hood until it is snug (do not over-tighten).

9. Replace the firebox components. Restore the fireplace to the correct configuration. Install the firebacks

before re-installing the burner.

10. Access the stepper motor (shown below). The stepper motor (adjustable regulator) has an installation sheet

included with it – make sure to follow all of the directions. Disconnect the wiring from the stepper motor.
Remove the stock stepper motor and replace it with the LP version. –

MAKE SURE IT IS CORRECTLY

ORIENTED

. Secure using the screws included with the motor – tighten to 25 Lb.-inches. Leak test this area

after installation to verify proper installation. Re-attach the wiring.

11. Restore the appliance to the correct configuration. Make the gas line connection, bleed the gas line (if

applicable), start the heater, and thoroughly leak-test all gas connections and the gas control valve.

7/16" Wrench

Natural Gas Orifice = .018N

LP (Propane) Orifce = .014LP

.018N

.014LP

Содержание 430 Mod-Fyre GSR2



































































Результаты поиска

Содержание 430 Mod-Fyre GSR2

Отзывы:

Бренды по названию

Популярные бренды

Travis Industries 430 Mod-Fyre GSR2, Руководство пользователя

Результаты поиска

Содержание 430 Mod-Fyre GSR2

Отзывы:

Бренды по названию

Популярные бренды