©2017 Thermaco, Inc. All rights reserved • Patented/Patents Pending • Specifications subject to change without notice
Thermaco, Inc. • 646 Greensboro St. • Asheboro, N. C. 27204-2548 • (336) 629-4651
MNL-TZ 12
A THERMACO® Technology
Trapzilla
®
Grease Interceptor
Installation and Operations Manual
TZ-160, TZ-400, TZ-600 Models
AFE
MNL-TZ 11
Note: Drawing for reference only. Equipment must be installed in compli-
ance with all applicable laws, regulations and codes, including plumbing
codes. Installation should be performed by a qualified plumber.
*Use a Two-Way Cleanout before
and after all Trapzilla Installations
1
1
2
2
3
3
4
4
A
A
B
B
C
C
D
D
THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
MATERIAL (UNLESS NOTED)
FINISH (UNLESS NOTED)
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX 336-626-5739
Decimals
.XX +/- .03
.XXX +/- .015
Unless otherwise specified
Dimensions are in inches
Tolerances
Angular
+/- 1°
CHECKED
SIZE
REV. NO.
DWG NO.
PART NO.
C
SCALE
RELEASE DATE
SHEET OF
ENGINEERING
DRAWN
DATE
THIRD ANGLE PROJECTION
Outlet
Inlet
*Cleanout
*Cleanout
Outlet Vent
(Connect to
facility vent)
3.3.2 Installing Two Trapzilla Units in Parallel
Two Trapzilla Grease Interceptors should be installed in parallel with a Flow Splitter diverting the flow.
Place Two-Way Cleanouts before, between and after the units as shown below, including before and
after the flow splitter. Make sure to connect an outlet vent after each Trapzilla Grease Interceptor. A
Low Head Flow Control (LHFC) is shipped with each unit, and if needed should only be installed after
the first Cleanout and before the Flow Splitter.
Note: Drawing for reference only. Equipment must be installed in compli-
ance with all applicable laws, regulations and codes, including plumbing
codes. Installation should be performed by a qualified plumber.
1
1
2
2
3
3
4
4
A
A
B
B
C
C
D
D
THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
MATERIAL (UNLESS NOTED)
FINISH (UNLESS NOTED)
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX 336-626-5739
Decimals
.XX +/- .03
.XXX +/- .015
Unless otherwise specified
Dimensions are in inches
Tolerances
Angular
+/- 1°
CHECKED
SIZE
REV. NO.
DWG NO.
PART NO.
C
SCALE
RELEASE DATE
SHEET OF
ENGINEERING
DRAWN
DATE
THIRD ANGLE PROJECTION
Cleanout*
Cleanout*
Cleanout*
Cleanout*
Outlet
Outlet
Inlet
Trapzilla
TZ-600 unit
Trapzilla
TZ-600 unit
*Use a 4" (100 mm) Two-Way Cleanout for TSS-70,
TSS-95, TZ-400 and TZ-600 Unit Installations
Outlet Vent
(Connect to
facility vent)
4" (100 mm) Flow Splitter
*Use a Two-Way Cleanout before and after all
Trapzilla Installations
Flow Splitter
3.3 Plumbing Configurations
3.3.1 Installing One Trapzilla Unit
Each Trapzilla unit is shipped with a Low Head Flow Control module (see LHFC box for additional
instructions). This needs to be installed to the inlet of the Trapzilla and connected to a code-approved
air intake. Thermaco, Inc. recommends installation of Two-Way Cleanouts on both the Inlet and Outlet
of Trapzilla
®
in accordance with all applicable laws, regulations and codes.
These cleanouts should
match the size of the Inlet and Outlet Piping (i.e. for 4” plumbing, a 4” cleanout should be used).
A Vent on the Outlet piping is also to be installed in accordance with all applicable laws, regulations and
codes.