Transition Networks SISTP10xx-141-LR Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 42

background image

Transition Networks

SISTP10xx-141-LR(T) Industrial PoE Switch

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

8

DIN rail mounting

DIN rail clip

The Industrial PoE Switch includes an aluminum DIN Rail Clip attached to the rear panel.
Verify the clip is attached and oriented as pictured in Figure 4 below.

Figure 4: Mounted DIN Rail Clip

DIN rail mounting
considerations

Consider the following before mounting the DIN rail to a surface and attaching the Industrial
PoE Switch:

•

The surface must support at least 450g

(1.0 lbs)

for the Industrial PoE Switch.

•

Do not place heavy objects on the Industrial PoE Switch.

CAUTION

Mount the Industrial PoE Switch with proper spacing around it for ventilation

(heat

dissipation)

. Failure to observe this caution could result in damage to the Industrial PoE

Switch.

CAUTION

Please exercise caution when using power tools. Do not install this unit in damp or wet
locations, or in close proximity to very hot surfaces. Failure to observe this caution could
result in damage to the Industrial PoE Switch and cables.

Continued on next page

DIN Rail Clip
(installed)

Screws (3)

Metal spring

«
...
14
15
16
17
18
...
»

Содержание SISTP10xx-141-LR











































Отзывы:

Нет отзывов

Похожие инструкции для SISTP10xx-141-LR

D DGS-3048 DGS-3048

Бренд: D-Link Страницы: 3

SANbox 5600 Series

Бренд: Qlogic Страницы: 408

Бренд: Edimax Страницы: 2

ZigBee Mini Hub

Бренд: ORVIBO Страницы: 3

Бренд: hager Страницы: 2

Бренд: Sarowin Страницы: 9

CentreCOM GS970M Series

Бренд: Allied Telesis Страницы: 21

Бренд: hager Страницы: 4

Бренд: Metrix Страницы: 12

Бренд: A-Neuvideo Страницы: 28

Бренд: N-Tron Страницы: 5

Бренд: LevelOne Страницы: 17

Бренд: Quartz Страницы: 43

Бренд: Crestron Страницы: 36

Summit X450-G2-24t-GE4

Бренд: Extreme Networks Страницы: 2

Бренд: A SYSTEMS Страницы: 80

Бренд: Rosewill Страницы: 9

Бренд: Wave Italy Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды