background image

PowerStar™ III

8

11

RJ-11 Pin Settings

Verify that the jumper locations activate the pins required for the
installation.

RJ-45 Pin Settings

Verify that the jumper locations activate the pins required for the
installation.

6. Rotate PowerStar™ III cover to rest again on chassis. 

7. Slide cover forward to engage cover against chassis.

8. Replace cover screws.

1

6

Top View
of the
RJ-11 Cable
Connector

1  2  3  4  5  6

Thick lines
indicate
pairs

Thin lines
indicate
pin leads

1

6

Crossview
of the RJ-11
Cable Connector

Top

2,5

3,4

1,6

PowerStar III Jumpers

PowerStar III Top Front

RJ-11 Pins

NOT USED

1  2  3  4  5  6  7  8

Top View
of the
RJ-45 Cable
Connector

Thick lines
indicate
pairs

Thin lines
indicate
pin leads

1

8

Crossview
of the RJ-45
Cable Connector

Top

3,6

4,5

1,2

7,8

PowerStar III Jumpers RJ-45 Pins

NOT USED

1

8

PowerStar III Top Front

Pin Settings

The default factory setting for both RJ-11 and RJ-45
configurations is two centered jumpers. This default
setting activates pins 3 & 4 in the RJ-11 connector and
pins 4 & 5 in the RJ-45 connector.

Connecting  Link Cable to Host

Connect the AS/400, Sys36, or 5x94 remote controller host to 
the PowerStar III using either twisted pair or twinax cable. 

NOTE: All cable lengths must be greater than 25 feet (7.6 meters).

Connecting Twisted Pair Link Cable

When installing twisted pair cable, attach a balun to the AS/400™ or
S/3x twinax port, then attach the twisted pair cable between the balun
and the RJ Link connector on the PowerStar III. 
CAUTION: Do NOT use a balun to connect twisted pair cable to
twinax cable. A mid-link media change may degrade the signal and
result in data loss
.  
NOTE: When twisted pair cable is used, compatible baluns must be
selected according to the chart on page 4, the RJ-11 or RJ-45
connector pin settings must be configured as shown on page 8, and
the polarity switch must be set as shown on page 10.

To connect link cable to PowerStar™ III link connectors:

1. Locate or build twisted pair cables that conform to

specifications on page 23 and to conditions noted above, with
minimum length of 25 feet (7.6 meters) and with male RJ-11
or RJ-45 plug connectors installed at both cable ends.

2. Connect male RJ-11 or RJ-45 plug connector at one end of

cable to a Link port on the PowerStar™ III RJ-11 or RJ-45 jack
connector.

3. Connect balun to the twinax port on the host computer.

4. Connect male RJ-11 or RJ-45 plug connector at other end of

cable to balun installed on the host in step 3.

Содержание PowerStar III













Отзывы: