background image

Transition Networks 

 

 

 

 

 

 

 

CPSMP-205 User Guide

 

Cautions and Warnings 

Definitions 

  CAUTIONS indicate potential damage to equipment. 

 Warnings indicate potential hazard or injury to people. 

Cautions and warnings in this manual 

Cautions and Warnings are explained here and placed throughout this manual where appropriate. 

 CAUTION: While installing or servicing the power supply, wear a grounding device and observe all electrostatic 

discharge precautions. Failure to observe this caution could result in damage or failure of the power supply. 

 WARNING: Do not connect the power supply to an external power source before installing it into the chassis. 

Failure to observe this warning could result in an electrical shock, even death. 

 WARNING: A readily accessible, suitable National Electrical Code (NEC) or local electrical code approved 

disconnect device and branch-circuit protector must be part of the building's installed wiring. Failure to observe this 
warning could result in an electric shock, even death. 

 WARNING: Turn the power supply and external power source OFF and ensure that the power supply is 

disconnected from the external power source before performing any maintenance. Failure to observe this warning 
could result in an electrical shock, even death.

 

 

33458 Rev. B 

http://www.transition.com/ 

Page 2 of 14 

Содержание CPSMP-205















Отзывы: