13
.
Cable Specifications
-- Continued
T1/E1 Cable
Category 3: (minimum requirement)
Connector:
RJ-48C
Electrical network connection:
Single 4-wire (Tip/Ring - Tip1/Ring1)
Mechanical arrangement:
8-position miniature modular jack
Usage:
1.544 Mb/s access lines
Interface codes:
04DU9 (any applicable)
Cable type:
Long Haul T1/E1:
0db, -7.5dp, -15db, -22db
E1:
E1 3.0V, 120 ohm
J1:
0-655’, 110 ohm
DSX-1:
0-133’, 133-266’, 266-399’,
399-533’, 533-655’, 100 ohm
4
5
Receive
Transmit
4
5
(ring) R1
(tip) T1
1
(ring) R
1
R
2
(tip) T
2
T
R1
T1
from the
media converter
to the
network
3
3
6
6
7
7
8
8
dry contact A
dry contact B
(not used)
RS-232 Cable
(included)
Connectors:
6-pin DIN and DB-9
Gauge:
24 to 22 AWG
Attenuation:
20 dB/1000 ft. @ 10 MHz
Differential characteristic impedance: 100 ohm +/- 10% @ 10 MHz
Maximum cable distance:
<10 ft (3.2 m) @ 56 kb/s or higher
DB-9
DIN 6-pin
9
8
7
6
1
5
4
3
2
2
1
4
6
3
5
Clear to Send
Signal Ground
5
9
Receive Signal
Transmit Data
3
2
Transmit Signal
Request to Send
7
1
Signal Ground
Receive Data
2
3,5
12
S4TEF10xx-10x
.
Cable Specifications
The physical characteristics must meet or exceed ITU specifications.
Fiber Cable
Bit Error Rate:
<10-9
Single mode fiber (recommended):
9 µm
Multimode fiber (recommended):
62.5/125 µm
Multimode fiber (optional):
100/140, 85/140, 50/125 µm
AS4TEF1011-100
1300 nm multimode
Fiber Optic Transmitter Power:
min: -19.0 dBm
max: -14.0 dBm
Fiber Optic Receiver Sensitivity:
min: -30.0 dBm
max: -14.0 dBm
Link Budget:
11.0 dB
AS4TEF1013-100
1300 nm multimode
Fiber Optic Transmitter Power:
min: -19.0 dBm
max: -14.0 dBm
Fiber Optic Receiver Sensitivity:
min: -30.0 dBm
max: -14.0 dBm
Link Budget:
11.0 dB
AS4TEF1014-100
1310 nm single mode
Fiber-optic Transmitter Power:
min: -15.0 dBm
max: -8.0 dBm
Fiber-optic Receiver Sensitivity:
min: -31.0 dBm
max: -8.0 dBm
Link Budget:
16.0 dB
AS4TEF1015-100
(long haul)
1310 nm single mode
Fiber-optic Transmitter Power:
min: -8.0 dBm
max: -2.0 dBm
Fiber-optic Receiver Sensitivity:
min: -34.0 dBm
max: -7.0 dBm
Link Budget:
26.0 dB
AS4TEF1016-100
(extra long haul)
1310 nm single mode
AS4TEF1017-100
(long wave length) 1550 nm single mode
Fiber-optic Transmitter Power:
min: -5.0 dBm
max: 0.0 dBm
Fiber-optic Receiver Sensitivity:
min: -34.0 dBm
max: -7.0 dBm
Link Budget:
29.0 dB
S4TEF1018-100
1300 nm multimode
Fiber-optic Transmitter Power:
min: -19.0 dBm
max: -14.0 dBm
Fiber-optic Receiver Sensitivity:
min: -30.0 dBm
max: -14.0 dBm
Link Budget:
11.0 dB
AS4TEF1029-100
13170 nm (TX)/1550 nm (RX) simplex
AS4TEF1029-101
1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power:
min: -13.0 dBm
max: -6.0 dBm
Fiber-optic Receiver Sensitivity:
min: -32.0 dBm
max: -3.0 dBm
Link Budget:
19.0 dB
AS4TEF1029-102
1310 nm (TX)/1550 nm (RX) simplex
AS4TEF1029-103
1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power:
min: -8.0 dBm
max: -3.0 dBm
Fiber-optic Receiver Sensitivity:
min: -33.0 dBm
max: -3.0 dBm
Link Budget:
25.0 dB
The fiber optic transmitters on this device meets Class I Laser safety
requirements per IEC-825/CDRH standards and complies with 21
CFR1040.10 and 21CFR1040.11.
