Trane VUV Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 40

Trane VUV Скачать руководство пользователя страница 28

28

UV-SVN03D-EN

WARNING

Hazardous Service
Procedures!

The maintenance and trouble-
shooting procedures recommend-
ed in this section of the manual
could result in exposure to electri-
cal, mechanical or other potential
safety hazards. Always refer to
the safety warnings provided
throughout this manual concern-
ing these procedures. When possi-
ble, disconnect all electrical
power including remote discon-
nects before servicing. Follow
proper lockout/tagout procedures
to ensure the power can not be in-
advertently energized. When nec-
essary to work with live electrical
components, have a qualified li-
censed electrician or other indi-
vidual who has been trained in
handling live electrical compo-
nents perform these tasks. Failure
to follow all of the recommended
safety warnings provided, could
result in death or serious injury.

Access to Fanboard & Motor

The unit ventilator fan board can be re-
moved for service to the blower motor
and fan wheels. The fan board must
also be removed for easier access to
the unit coils for cleaning and mainte-
nance. Utilize the following steps for
proper removal of the fanboard.

1

Turn off power to the unit and re-

move the front panel.

2

Disconnect P-trap from drain pan.

3

Disconnect fan plug.

4

Slide fan board by pulling deck

forward,

Figure 17

.

CAUTION

Equipment Damage!

Support the fanboard to prevent
the deck from sliding too far for-
ward and falling out of the unit.
Failure to do so may cause equip-
ment damage.

5

When reinstalling, use the same

steps in reverse order.

Motor

The fan motor is a permanent split ca-
pacitor type motor with voltage specif-
ic power. See Table E1 through E3 for
electrical performance and motor volt-
age.

Table E3:

Motor Voltage

If a replacement motor is required, it
should be ordered from The Trane
Company. To replace the fan motor,
complete the following steps:

6

Complete steps for removal of
fan board.

7

Disconnect the motor ground
wire.

8

Using a 7/16” Allen wrench, loos-
en the coupling on the fan shaft.

9

Loosen the screw on the motor
clamp until it allow the motor to
be lifted off the base,

Figure 18

.

10

Lift the motor and pull forward
until fan shaft separates from the
motor,

Figure 19

.

Unit Voltage

Motor Voltage

115-60-1

115-60-1

208-60-1

208/230-60-1

230-60-1

208/230-60-1

208-60-3

208/230-60-1

460-60-3

265-60-1

265-60-1

265-60-1

230-60-3

208/230-60-1

11

Attach new motor to fan shaft
and reverse steps to complete in-
stallation.

Maintenance

!

Figure 17:

Fan board removal for fan/

motor access

Figure 18

: Loosen screws

Figure 19

: Lift/pull motor forward

«
...
26
27
28
29
30
...
»

Содержание VUV









































Отзывы:

Нет отзывов