Trane TSC060ED Скачать руководство пользователя страница 5

Model Number Descriptions

RT-SVX37B-EN

E

Clogged Filter Switch

14

, Fan Failure

Switch

14

 and Condensate Drain Pan 

Overflow Switch

F

Clogged Filter Switch

14

, Discharge

Air Sensing Tube

14

 and Condensate

Drain Pan Overflow Switch

G

Fan Failure Switch, Discharge Air
Sensing Tube

14

 and Condensate

Drain Pan Overflow Switch

H

Clogged Filter Switch

14

, Fan Failure 

Switch

14

, Discharge Air Sensing

14

and Condensate Drain Pan Overflow 
Switch

Digit 26 - System Monitoring 
Controls

0

No Monitoring Controls

A

Demand Control Ventilation 

(CO

2

)

30

,

31

Digit 27 - Unit Hardware 
Enhancements

0

No Enhancements

1

Stainless Steel Drain Pan

Model Number Notes

1.

Available on 3-5 ton models.

2. Standard on 4-5 Ton E3,4,W and 

6-10 Ton Heat Pumps and all High 
Efficiency models. 

3. Not available with 

electromechanical controls.

4. Manual outside air damper will 

ship factory supplied within the 
unit, but must be field installed.

5. High pressure control is standard 

on all units.

6. On 3-5 ton, multispeed direct 

drive is standard on single phase 
and 15 SEER. On 6-10 ton, 
multispeed direct drive is 
standard on all 10 ton and 7.5-8.5 
ton high efficiency. Belt drive is 
standard on all other units.

7.

Economizer with Barometric 
Relief is for downflow configured 
units only. Order Economizer 
without Barometric Relief for 

horizontal configuration. 
Barometric Relief for horizontal 
configured units must be ordered 
as field installed accessory.

8. Through the base electric 

required when ordering 
disconnect/circuit breaker 
options.

9. Requires use of Disconnect or 

Circuit Breaker. 

10. Standard metering devices are 

TXVs. 

11. Frostat cannot be field installed in 

electro-mechanical units. 

12. The return air smoke detector 

may not fit up or work properly on 
the Precedent units when used in 
conjunction with 3rd party 
accessories such as bolt on heat 
wheels, economizers and power 
exhaust. Do not order the return 
air smoke detectors when using 
this type of accessory. 

13. Return Air Smoke Detector 

cannot be ordered with Novar 
Controls.

14. These options are standard when 

ordering Novar Controls.

15. This option is used when 

ordering Novar Controls.

16. Not available with high 

temperature duct sensor 
accessory.

17. Digit 15 = 2 

18. Novar Sensor utilized with 

Digit 21 = (4) Novar 3051 Controls 
without Zone Sensor.

19. Available for 10 ton standard 

efficiency models only.

20. Available for 3, 4, 5, 6, 7½, 8½ ton 

standard/high efficiency models 
only.

21. Requires selection of 2” Pleated 

Filters (option B or C) for Digit 16.

22. Not available on 6 ton units and 

all single phase or standard 
efficiency. 

23. Standard on TSC 6, 7½ (single 

and dual systems), 8½, 10 ton 
standard efficiency models and 
THC 4, 5, 6, 7½ ton high efficiency 
models (except for 
dehumidification models).

24. Epoxy coil and epoxy with 

hailguard options are not 
available for units with 
microchannel condenser coil.

25. Single Zone VAV is only available 

on 7.5-10 ton high efficiency and 
10 ton standard efficiency 
products with ReliaTel™ controls. 

26. Multi-speed indoor fan available 

only on 7.5 & 8.5 ton high 
efficiency, and 10 ton products 
with ReliaTel™ controls.

27. Motorized Outside Air Damper is 

not available on Multi-Speed or 
SZVAV (Single Zone Variable Air 
Volume) products.

28. Frostat standard on Multi-Speed 

and SZVAV (Single Zone Variable 
Air Volume)

 

products.

29. Novar is not available with SZVAV 

products.

30. Demand Control Ventilation not 

available with electromechanical 
controls.

31. Demand Control Ventilation 

Option includes wiring only. The 
C0

2

 sensor is a field-installed only 

option.

Digit 15 = 0

Standard Efficiency
1 Phase = High Efficiency Multispeed Direct 
Drive Motor
3 Phase (3-8½ Ton) = Belt Drive
3 Phase (10 Ton) = Ultra High Efficiency Direct 
Drive Plenum Fan
High Efficiency
1 Phase = High Efficiency Multispeed Direct 
Drive Motor
3 Phase (3-5 ton) = High Efficiency Multispeed 
Direct Drive Motor
3 Phase (3-5 ton w/Dehumidification) = Belt 
Drive Motor
3 Phase (7½-10 ton) = Ultra High Efficiency 
Direct Drive Plenum Fan

Not Available

Standard Efficiency
10 Ton w/575V
High Efficiency
3-5 ton w/Standard Indoor Motor w/460V

Standard Efficiency
1 Phase = Not Available
3 Phase = Not Available
High Efficiency
1 Phase = Not Available
3 Phase (3-5 ton) = 

May be Ordered

3 Phase (3-5 ton w/Dehumidification) = Not 
Available
3 Phase (6-10 ton) = Not Available

Содержание TSC060ED













































Отзывы: