Trane Tracer ZN521 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 60

background image

48

CNT-SVX07D-EN

Status indicators for operation and communication

The yellow (communications) LED on the Tracer ZN521 controller (see Figure 19 on page 43)
indicate the controller’s communication status (see

Diagnostics

Diagnostics are informational messages that indicate the operational status of the controller. In
response to most diagnostics, the controller attempts to protect the equipment by enabling or
disabling, or opening or closing, specific outputs. Other diagnostics provide information about the
status of the controller, but have no effect on outputs. Diagnostics are reported in the order in which
they occur. Multiple diagnostics can be present simultaneously. Diagnostic messages are viewed
using the Rover service tool or through a BAS.

Types of diagnostics

Diagnostics are categorized according to the type of clearing method each uses and the type of
information each provides.

The four categories are:

•

Manual (latching)

•

Automatic (nonlatching)

•

Smart reset

•

Informational

Note:

Clearing diagnostics refers to deleting diagnostics from the software; it does not affect the
problem that generated the message. For help with diagnosing a problem, see

“Troubleshooting,” p. 51

.

Manual (latching) diagnostics

Manual diagnostics (also referred to as

latching

) cause the unit to shut down. Manual diagnostics

can be cleared from the controller in one of the following ways:

•

By using the Rover service tool (see “Resetting a diagnostic” in EMTX-SVX01A-EN,

Rover

Installation/Operation/and Programming

guide)

.

•

Through a building automation system (see product literature)

•

By initiating a manual output test at the controller (see “Manual output test” on page 43)

•

By cycling power to the controller. When the 24 Vac power to the controller is cycled off and then
on again, a power-up sequence occurs.

•

By turning the zone sensor fan switch to

OFF

and then back to any other setting. (This feature

will be available beginning with controller software version 2.10.)

Automatic (nonlatching) diagnostics

Automatic diagnostics clear automatically when the problem that generated the diagnostic is
solved.

Table 15. Yellow LED: Communications indicator

LED activity

Explanation

LED is off continuously

The controller is not detecting any

communication (normal for stand-alone

applications).

LED blinks.

The controller detects communication (normal

for communicating applications, including

data sharing).

LED is on continuously.

Problem with communication link wiring

(possible need for termination resistor), or

controller failure (caused by power surge,

lightning strike, etc.)

«
...
46
47
48
49
50
...
»

Содержание Tracer ZN521





























































Отзывы:

Нет отзывов

Похожие инструкции для Tracer ZN521

Бренд: Ubisys Страницы: 2

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: KEENZ Страницы: 24

Бренд: BEIER-Electronic Страницы: 22

Бренд: Hanwell Страницы: 34

Бренд: HANSONG Страницы: 11

Бренд: Datapath Страницы: 12

Бренд: Hansen Страницы: 4

Бренд: Mamas & Papas Страницы: 24

Бренд: Mamas & Papas Страницы: 24

Бренд: Vacon Страницы: 132

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: WAGO Страницы: 16

Бренд: bihl+Wiedemann Страницы: 16

Tracer CH.530 RLC-SVU01B-E4

Бренд: Trane Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды