Trane RAUS 040 Скачать руководство пользователя страница 25

Страница: 25 / 36

Page 25

CHECK LIST – MANDATORY OPERATION CONTROL BEFORE

START-UP

DATE

UNIT

GENERAL

COMPLIANCE

YES NO

THE UNIT DISPLAYS DENTS OR DAMAGES ON THE EXTERNAL CASING OCCURRED DURING THE TRANSPORTATION

OR POSITIONING.

IF ANY, SPECIFY BELOW:

WARNING:

PLEASE BE AWARE THAT RELEVANT DAMAGES CAUSED BY THE QUOTED CIRCUMSTANCES MAY RESULT

IN THE CALL-OFF OF THE WARRANTY.

THE UNIT HAS BEEN INSTALLED IN ACCORDANCE WITH THE MINIMUM DISTANCE PROVIDED IN THE DIMENSIONAL

DRAWING AND TECHNICAL DOCUMENTATION PROVIDED.

THE UNIT IS INSTALLED NEXT TO THE: PHOTOVOLTAIC SYSTEM, ELECTRONIC TRANSMITTERS,ANTENNAS OR SIMILAR

DEVICES.

THE UNIT IS POSITIONED ON A PERFECTLY FLAT (NOT INCLINED) SURFACE.

ANTI-VIBRATIONS DAMPERS HAVE BEEN INSTALLED BETWEEN THE UNIT AND THE FLOOR.

THE UNIT DISPLAYS DEFECTS OR DAMAGES RESULTING FROM MODIFICATIONS OR CHANGES (UNIT TAMPERING /

UNAUTHORIZED MODIFICATIONS TO THE REFRIGERANT CIRCUIT OR THE HYDRAULIC CIRCUIT OR THE ELECTRICAL

PANEL OR CHANGES TO THE UNIT OPERATING PARAMETERS) MADE BY A THIRD PERSON WITHOUT A WRITTEN

AUTHORIZATION ISSUED BY TRANE. THE UNIT SHALL BE CONFORM TO TRANE WIRING DIAGRAMS AND TECHNICAL

DOCUMENTATION) IN CASE OF RELEVANT DIFFERENCE BETWEEN THE UNIT AND TRANE STANDARD

CONFIGURATION PLEASE CONTACT TRANE.

WARNING:

PLEASE BE AWARE THAT RELEVANT DAMAGES CAUSED BY THE QUOTED CIRCUMSTANCES MAY RESULT

IN THE CALL-OFF OF THE WARRANTY.

THE UNIT HAS BEEN INSTALLED VERY CLOSE TO

A MARINE ENVIRONMENT

OR AN

AGGRESSIVE INSTALLATION

ENVIRONMENT

(HIGHLY CORROSIVE CHEMICAL AGENT).

WARNING:

PLEASE BE AWARE THAT RELEVANT DAMAGES CAUSED BY THE QUOTED CIRCUMSTANCES MAY RESULT

IN THE CALL-OFF OF THE WARRANTY.

SPOTTED PRESENCE OF MOLD, MUSHROOMS, BACTERIA, MICROBIAL OF ANY TYPE.

THE UNIT DISPLAYS DAMAGES CAUSED BY: FLOODS, LIGHTNING, FIRE, ANY ACCIDENT BEYOND TRANE CONTROL.

SITE:
ADDRESS:

POSTCODE:

COUNTRY:

THE INTENDED PURPOSE OF RAUS / RAUX UNITS IS NOT FOR INDUSTRIAL PROCESS APPLICATION. PLEASE CONTACT TRANE TECHNICAL

DEPARTMENT IN CASE OF INDUSTRIAL PROCESS APPLICATION.

CUSTOMER:

Содержание RAUS 040





































Результаты поиска

Содержание RAUS 040

Отзывы:

Похожие инструкции для RAUS 040

Бренды по названию

Популярные бренды

Trane RAUS 040, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание RAUS 040

Отзывы:

Похожие инструкции для RAUS 040

Бренды по названию

Популярные бренды