Trane GVAF Series, Установка, эксплуатация и обслуживание

Страница: 23 / 56

CTV-SVX009D-GB 23 11 UNT-PRC002-GB
Sound power levels
Discharge
Measurement conditions:
Measurements taken in a room adjacent to the room containing the FWD, at the outlet of the rectangular duct (1.5 m
long) fixed to its discharge opening.
Fan Power level in dB(A), per Hz frequency band Overall power
Unit speed 125 250 500 1000 2000 4000 8000 dB(A)
1 55 50 42 37 37 31 30 46
FWD 08 2 57 54 47 40 30 38 40 50
3 58 57 50 42 32 40 43 53
1 57 51 45 42 34 33 28 48
FWD 10 2 58 54 48 45 38 39 35 51
3 60 58 50 48 40 42 39 54
1 57 51 45 42 34 33 28 48
FWD 12 2 58 54 48 45 38 39 35 51
3 60 58 50 48 40 42 39 54
1 56 62 50 48 39 38 36 56
FWD 14 2 61 66 55 53 47 46 45 60
3 63 69 58 56 50 50 49 63
1 57 63 51 49 40 39 37 57
FWD 20 2 61 66 55 53 47 46 45 60
3 63 69 58 56 50 50 49 63
Intake
Measurement conditions:
Measurements taken at the horizontal air intake.
Fan Power level in dB(A), per Hz frequency band Overall power
Unit speed 125 250 500 1000 2000 4000 8000 dB(A)
1 56 55 55 53 46 45 42 57
FWD 08 2 63 62 60 60 53 53 53 64
3 66 65 63 62 56 55 57 67
1 62 58 55 58 51 48 44 61
FWD 10 2 66 63 60 62 56 55 52 66
3 70 67 63 65 59 59 57 69
1 62 58 55 58 51 48 44 61
FWD 12 2 66 63 60 62 56 55 52 66
3 70 67 63 65 59 59 57 69
1 66 65 65 65 57 50 46 68
FWD 14 2 73 72 69 71 64 59 57 74
3 78 76 73 75 69 64 63 78
1 68 72 64 64 56 52 50 69
FWD 20 2 76 76 68 71 65 61 61 75
3 78 79 71 74 69 66 66 78
Optional Integrated Pump Package
Figure 9
–
Hydraulic module water chart
CHILLED WATE
R
5
Pi
1
2 3 4 4
5
6
7
9
TT
TT
8
8 8
8
8
4 5
5
1 = Twin centrifugal pump
2 = Water strainer
3 = Balancing valve
4 = Drain valve
5 = Valve for pressure point
6 = Expansion tank
7 = Pressure relief valve
8 = Antifreeze protection
9 = Evaporator
Pi = Gauge
TT = Temperature sensor
Chiller can be ordered with an optional integrated
hydraulic module. In this case, chiller will be provided
with the following components factory mounted and
tested:
• Twin centrifugal water pump, Low pressure or High
pressure (option)
• Water strainer to protect the pump against impurities in
the circuit
• Expansion module with expansion vessel and pressure
relief valve sufficient to ensure the expansion of the
water loop ability
• Thermal insulation for antifreeze protection
• Balancing valve for equilibrate the flow of water circuit
• Drain valve
• Temperature sensor
Note: A pressure switch device to detect lack of water
is not included in the pump package. Installation of this
type of device is highly recommended to avoid sealing
damage due to operation of pump without enough water.