background image

ACC-SVN264B-EN

General Information - FIAECON103*

This section covers installation of low leak economizers for 
12.5 to 25 ton downflow units in the D cabinet (digit 39 = D).

Inspection 

1. Unpack all components of the kit.
2. Check carefully for shipping damage. If any damage is 

found, report it immediately, and file a claim against the 
transportation company.

3. Visually inspect the components for shipping damage as 

soon as possible after delivery, before it is stored. 
Concealed damage must be reported within 15 days.

4. If concealed damage is discovered, stop unpacking the 

shipment.

5. Do not remove damaged material from the receiving 

location. Take photos of the damage, if possible. The 
owner must provide reasonable evidence that the damage 
did not occur after delivery.

6. Notify the carrier’s terminal of damage immediately by 

phone and by mail. Request an immediate joint inspection 
of the damage by the carrier and the consignee.

Note:

Do not attempt to repair any damaged parts until the 
parts are inspected by the carrier’s representative.

Parts List

NOTICE

Corrosion Damage!

Failure to use recommended caulking/sealant could 

cause corrosion related failures to refrigerant 

components.

1

2

3

4

5

6

8

7

Carton A

Carton B

9

10

11

12

13

Outside Air Damper

Figure 10. Low leak economizer (12.5 to 25 tons - downflow)

Содержание FIAECON102 Series





















Отзывы: