background image

WARNING

Follow EHS Policies!

Failure to follow instructions below could result in 

death or serious injury.

All Trane personnel must follow the company’s 
Environmental, Health and Safety (EHS) policies 
when performing work such as hot work, electrical, 
fall protection, lockout/tagout, refrigerant handling, 
etc. Where local regulations are more stringent than 
these policies, those regulations supersede these 
policies. 

Non-Trane personnel should always follow local 
regulations.

Introduction

ACC-SVN264B-EN

Copyright

This document and the information in it are the property of 
Trane, and may not be used or reproduced in whole or in part 
without written permission. Trane reserves the right to revise 
this publication at any time, and to make changes to its content 
without obligation to notify any person of such revision or 
change.

Trademarks

All trademarks referenced in this document are the trademarks 
of their respective owners. 

Revision History

Updated Installation - FIAECON102* chapter.

Updated FIAECON102*- General Information chapter.

Updated FIAECON103*- General Information chapter.

Содержание FIAECON102 Series





















Отзывы: