background image

21

Installation (Continued)

Table 3-3

Customer Connection Wire Range

Table 3-4

Unit Electrical Data

Allowable

Minimum

Maximum

Dual

Condenser Fan Motors

Unit

Rated

Voltage

Circuit

Fuse

Element

HP

FLA

LRA

KW

Size

Voltage

Range

Ampacity

Size

Fuse

Qty.

(Each) (Each) (Each) (Each)

200/230/60/3

180-220/208-254

9.2

15

15

2

1.0

4.1

20.7

0.9

C20

460/60/3

416-508

4.1

15

15

2

1.0

1.8

9.0

0.9

575/60/3

520-635

3.2

15

15

2

1.0

1.4

7.2

0.9

200/230/60/3

180-220/208-254

13.3

20

15

3

1.0

4.1

20.7

0.9

C25

460/60/3

416-508

5.9

15

15

3

1.0

1.8

9.0

0.9

575/60/3

520-635

4.6

15

15

3

1.0

1.4

7.2

0.9

200/230/60/3

180-220/208-254

13.3

20

15

3

1.0

4.1

20.7

0.9

C30

460/60/3

416-508

5.9

15

15

3

1.0

1.8

9.0

0.9

575/60/3

520-635

4.6

15

15

3

1.0

1.4

7.2

0.9

200/230/60/3

180-220/208-254

17.4

20

20

4

1.0

4.1

20.7

0.9

C40

460/60/3

416-508

7.7

15

15

4

1.0

1.8

9.0

0.9

575/60/3

520-635

6

15

15

4

1.0

1.4

7.2

0.9

200/230/60/3

180-220/208-254

25.6

30

30

6

1.0

4.1

20.7

0.9

C50

460/60/3

416-508

11.3

15

15

6

1.0

1.8

9.0

0.9

575/60/3

520-635

8.8

15

15

6

1.0

1.4

7.2

0.9

200/230/60/3

180-220/208-254

25.6

30

30

6

1.0

4.1

20.7

0.9

C60

460/60/3

416-508

11.3

15

15

6

1.0

1.8

9.0

0.9

575/60/3

520-635

8.8

15

15

6

1.0

1.4

7.2

0.9

Notes:
1. Electric information is for each individual motor.
2. Minimum Circuit Ampacity is 125% of the RLA of one motor plus the RLA of the remaining motors.
3. Maximum Fuse Size is 300% of the RLA of one motor plus the RLA of the remaining motors.
4. Recommended Dual Element Fuse Size is 225% of the RLA of one motor plus the RLA of the remaining motors.
5. RLA is rated in accordance with UL Standard 465.
6. Local codes may take precedence.

Содержание CAUC-C20













































Отзывы: