Trane 4TEE3F31B1000B Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 16

Trane 4TEE3F31B1000B Скачать руководство пользователя страница 3

18-GE04D2-15

3

Installer’s Guide

12. Make sure there are provisions for installing con-

densate drain lines.

13. If side, front or rear return is required, the air han-

dler must be elevated. Pedestal (TAYPLNM100)
may be used for 4TEE3F37. Pedestal
(TAYPLNM101) may be used for 4TEE3F40, 49, 65,
& 66.

14. Route refrigerant & condensate drain lines away

from air handler so they do not interfere with ac-
cess panels and filters.

15. When external accessories are used, the additional

height and width requirements must be considered
in the overall space needed.

16. These units are not approved for outdoor installa-

tion.

17. These units are approved for draw-through application

only.

18.

Flow-through Bypass Humidifiers

Excessive bypass air may cause water blow-off,
which will adversely affect system operation and air
cleaner performance. To verify bypass airflow, fol-
low the Bypass Humidifier Pre-Installation Check-
out and Set-Up Procedures available through your
local distributor. Ask for publication number 18-
CH37D1, latest revision.

Steam and Flow-through Fan Power Duct-
mounted Humidifiers

Follow the humidifier installation instructions.
These should only be installed on the supply air
side of the system. Atomizing style humidifiers are
not recommended with the use of this unit.

C. UNIT INSTALLATION

UPFLOW

a.

For maximum efficiency

, the horizontal drip

tray should be removed. See Figures 5, 6 and 7.

B. Two Piece Cabinet Disassembly

(OPTIONAL)

NOTE: For easier installation into tight areas, the 4 and
5 ton air handlers can be disassembled and reas-
sembled after moved to an attic or other space.

Steps for disassembly and reassembly (See Figures 3
and 4)

Figure 3 Closeup of Spear Locations

SCREWS 5-8
LOCATED ON
LEFT SIDE

1

2

3

4

From Dwg. 21B140413

4"

6"

17"

1"

3/8"

1/4" HOLES (4)

ACCESSORY BAY99X123

IF AIRHANDLER IS USED

WITHOUT

A FACTORY FURNISHED

SUPPLEMENTARY HEATER, A PLATE IS REQUIRED TO COVER
THE OPEN HOLE IN THE AIR FLOW SYSTEM

Figure 2

1.

Disconnect wiring.

2.

Remove center bracket.

3.

Remove blower assembly.

4.

Remove coil.

5.

Cut foil tape - minimum 3" foil tape.

6.

Remove top 8 screws. See Figure 3.

7.

Lift upper section.

8.

Set air handler in place.

9.

Attach screws - insure gaskets are aligned along
flange.

10. Use foil tape to seal - use minimum 3" foil tape.
11. Insert coil.
12. Reinstall blower assembly.
13. Reinstall center bracket.
14. Reconnect wiring.

NOTE: In Downflow, remove coil before blower by re-
versing steps 3 and 4.

2 Piece Wrapper Spear

Figure 4

«
1
2
3
4
5
...
»

Содержание 4TEE3F31B1000B

















Отзывы:

Нет отзывов