Trakka Corp Trakkabeam A800 Скачать руководство пользователя страница 71

Страница: 71 / 132

COMPONENT MAINTENANCE MANUAL

Publication No. 051019-1 Rev H

Page 71

33-46-00

AS9100 Certified

Rev G

26-Mar-2014

G. Lamp Assembly Removal

CAUTION:

BEFORE BEGINNING ANY WORK ON THE SEARCHLIGHT, ENSURE THE LAMP

ASSEMBLY IS IN A HORIZONTAL POSITION. THIS WILL MAKE THE WORK OF

REMOVING THE ASSEMBLY EASIER AND SAFER.

(1) Remove all power from the searchlight system.
(2) Disconnect the power and control connectors (Figure 52) from the dovetail assembly (033053).

Figure 52 - Removal of Lamp Assembly

(3) Remove the four rear retaining screws (Figure 52, item 4) (109666).
(4) Remove the three front retaining screws (Figure 52, item 3) (109666).

CAUTION:

WHEN REMOVING THE LAMP ASSEMBLY TAKE CARE THAT THE

ASSEMBLY DOES NOT GET CAUGHT ON THE LASER POINTER CABLE AT

THE BACK END OF THE REAR CASE.

(5) Rotate the lamp assembly (Figure 52, item2) (032054) counter clockwise approximately 25 mm

(1”) and then pull until the lamp assembly wiring is exposed.

WARNING: VOLTAGES OF UP TO 10,000 VOLTS MAY STILL BE PRESENT.

BEFORE CARRYING OUT ANY FURTHER ACTIONS WITH THE LAMP

ASSEMBLY, ENSURE THERE IS NO RESIDUAL VOLTAGE AT THE LAMP

TERMINALS.

(6) Connect a 10 ohm 10 Watt resistance across the lamp terminals to quickly discharge any

remaining residual voltage in the lamp. Refer to Figure 52.

(7) Test for zero voltage at the terminals with the aid of a multimeter to ensure that any residual

voltage that may have been present has been discharged.

(8) Remove the heatshrink from the two ignitor power cable connectors (Figure 52, item 5).

NOTE: Remove cable ties as required to access the connectors.

(9) Disconnect the three Molex connectors that connect to the lamp assembly from the gimbal arm

(Figure 52, item 5).

NOTE: The laser pointer connector does not need to be disconnected for this operation

but disconnection is recommended to avoid damage to the connector during

work.

A305

Counter Clockwise

Forward

Power and Control

Connectors

10 10W

AIRBUS HELICOPTERS: CMM L334M6304E01 ISSUE: B PAGE 89 OF 165

The document reference is online, please check the correspondence between the online documentation and the printed version.

Содержание Trakkabeam A800





































































































































Результаты поиска

Содержание Trakkabeam A800

Отзывы:

Похожие инструкции для Trakkabeam A800

Бренды по названию

Популярные бренды

Trakka Corp Trakkabeam A800, Руководство по техническому обслуживанию компонентов

Результаты поиска

Содержание Trakkabeam A800

Отзывы:

Похожие инструкции для Trakkabeam A800

Бренды по названию

Популярные бренды