background image

Model DUMPTR-3 Dump Truck Bed 

Revised 1/17/2015 

 

 

 

 

2 of 5 

 

Use and Warnings 

 

Your child’s safety is our top priority. Please observe the following safety warnings to ensure 
the safe use of this product: 

 Mattress size: This bed is intended for use only with a standard full mattress 74” - 75” 

long by 52 1/2” - 53 1/2” wide (mattress not included). Use of an incorrectly sized 
mattress may leave space between the edge of the mattress and the edge of the bed. 
Excess space may result in entrapment which may lead to serious injury or death. 

 Weight limitation: minimum weight requirement for this bed is 50 lbs. This product is not 

to be used by any occupant under 50 lbs. Do not let any child under 50 lbs. play or sleep 
on or around the bed. Maximum weight is 350 lbs. 

 Do not stand or sit on shelf. 

 Do not stand, sit, or otherwise occupy or apply weight to bed slats until a mattress or box 

spring has been installed. The slats are not rated or tested for individual loads without the 
application of mattress or box spring. 

 Do not allow jumping or horseplay on the bed. 

 Do not use bed if any parts are missing or damaged. 

 Do not use substitute parts. Contact manufacturer should replacement parts be 

necessary. 

 Do not use a water or sleep flotation mattress. 

 Before assembly and use, inspect bed for damaged hardware, loose joints, missing 

pieces or sharp edges. 

 Warning: hardware included with this product may have sharp points or edges. Assembly 

by an adult is required. Keep all loose hardware out of reach of children. 

 Warning: small parts are a choking hazard for children. Make sure that all hardware is 

properly and tightly installed to prevent access to loose parts by children. Properly discard 
excess hardware after assembly to prevent access of loose parts to children. Properly 
discard all packing materials. 

 Always make sure the mattress is firmly seated against the headboard. Excess space 

may result in entrapment which may lead to serious injury or death. 

Important Information 

 

Each one of our beds is handmade, hand painted, and hand packaged. Minor imperfections 
may occur that are not manufacturing defects, but rather a result of the handcrafting process 
that makes our beds unique and special. 

General Specifications 

 

Assembled dimensions (approximate): 89" long, 54.5" wide, 24" high 

Disassembly 

 

To disassemble, reverse order of steps for assembly. 

Содержание DUMPTR-3






Отзывы: