Trade-wind PMB02 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 11

Trade-wind PMB02 Скачать руководство пользователя страница 6

Installation Instructions Revised 10/13/2015 Copyright (C) 2008 Proverbs 22:29 Page 6

6

INSTRUCTIONS:

A 15 to 20 amp electrical service is recommended for proper electrical supply. Before

determining, calculate amp ratings based on the product label found on the PMB series module.  Always observe
local building codes.  Always use a dedicated circuit.  Line load is calculated by adding the amperage of the
halogen lights to the rated amperage of the ventilator..  If the ventilator is rated in watts rather than amps, divide the
watts by 120 and this will give you the amperage rating.

CAUTION:

The neutral wire (usually white) for the ventilator must connect to the same neutral wire that

comes from the electrical panel to the liner. It is recommended to run a white neutral wire from the liner’s white
neutral wire along the same path as the red wire from the liner’s variable speed control to the ventilator.

Factory Installed Variable-Speed Wiring Details

Black

120 volt AC from electrical panel (usually black)

White

Neutral from electrical panel (white)

Green

Ground from electrical panel (usually green)

Wiring Diagram

PMB Series Models

Liner

House Electrical

Panel

Green

White (N)

120V Black (L)

«
...
4
5
6
7
8
...
»

Содержание PMB02












Отзывы:

Нет отзывов