（1）.按“Dec（-）”或“Inc（+）”选择“三通”选项标题下的数值，按“Enter”按键选择此选项下的任意数值
数字闪动，按“Dec（-）”减小百分比数值，左侧数值至少调整到20%，右侧数值至少调整到10%，按“Enter”键
确认；
press “Dec(+)”or “Dec(-)” to select the percent in the “CH3”, press “Enter”, the percent flash, press
“Dec(+)”or “Dec(-)” to make it to be “20%” on the left and 10% on the right.
3.2WD/4WD切换功能的调试（2WD/4WD Shift adjusting ）：
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
[单边舵量]
舵机：100% 100%
油门：100% 100%
三通：20% 10%
20%
（2）.将对应舵机的插头插回接收机的第三通道，请注意正负极，开始调试舵机舵量；
Plug the corresponding servo cable into the receiver’s Channel 3. Please notice the place of anode and
cathode, then adjusting the “EPA”(Please make sure the car is power on,throttle servo and steering
servo is active), overhead the 4 wheels to make the wheels off the ground.
（3）.将“三通”选项下左侧的数值加大，留意车架上舵机的动态，加大到如图.3所示状态下红色固定座尽可能远离
波箱壳体并且舵机没有“滋滋”的响声即可，此时加大油门，看此时的红色固定座有没有位置变化和前轮是否转动
如没有顺时针旋转遥控器上的“VR”旋钮，使舵机变换到相反方向，车架上舵机臂位置如图.4所示，调整“三通”
选项下右侧的数值，同时加大车子油门，使其增大或减小到舵机没有响声即可，之后检查切换功能是否正常；
Increase the left percent gradually in the CH3 option, pay attention to the state of the shift servo, increase
to be shown as “Chart 3”, the red mount is as far away from the gearbox as possible and the servo has
no “Zizizi” sound. Then pull the throttle trigger, if the red mount’s position has no change and the
front wheels don’t turn, rotate the “VR” knob clockwise to shift the servo direction, the position of the
servo arm is shown as “Chart 4”, increase the right percent gradually in the CH4 option,then pull throttle
trigger a little. Repeat the step till the servo has no “Zizizi” sound. Finally check the 2WD/4WD shifting
function.
4.前后差速锁的调试(Front and rear diff Lock adjusting)：
（1）.将前/后差速锁舵机的插头插回接收机的第五/六通道，请注意正负极，开始调试舵机舵量（请确保车子通电，油门和转向舵机都有反映），架空车
子的四个轮胎；
Plug the corresponding servo cables into the receiver’s Channel 5 and channel 6. Please notice the place of anode and cathode, then
adjusting the “EPA”(Please make sure the car is power on,throttle servo and steering servo is active), overhead the 4 wheels to make
the wheels off the ground
（2）.向后拨动遥控器上的拨档开关此状态为差速器的锁止状态，车架上对应舵机状态如图.5所示，用手转动前后单侧车轮，检查差速锁是否锁止，如没
有锁止，请检查拉线是否过紧，松开拉线夹紧机米螺丝，检查差速器是否锁止，如锁止，上紧机米螺丝即可；
Pull back the toggle switch, the diff locks,the state is shown as “Chart 5”, check if the wheels turn by hand. If the wheels turn, maybe the
cable is too tight, loose the set screw to adjusting the cable till the diff locks,then tighten the set screw.
（3）.向前拨动遥控器上的拨档开关，此状态为差速器的打开状态，车架上对应舵机状态如图.6所示，用手转动前后单侧车轮，检查差速锁是否打开，如
感觉拉线过紧，请检查拉线两端是否插入到相应的凹槽内；
Push the toggle switch, the diff unlocks,the state is shown as “Chart 6”, check if the wheels turn by hand. If the wheels not turn, check if
the cable is too tight, then check if both ends of the cable are plugged into the corresponding groove
图.3 2WD舵机状态
Chart.3 2WD servo state
图.4 4WD舵机状态
Chart.4 4WD servo state
图.6差速打开舵机状态
Chart.6 Diff unlock servo state
图.5差速锁止舵机状态
Chart.5 Diff lock servo state
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
[EPA]
ST ：100% 100%
TH ：100% 100%
CH3 ：20% 10%
20%
THANK YOU!
3
