2.双速变速箱的调试(Two-speed adjusting)：
注意：调试前请再次确认接收机接线图、车架功能舵机位置和遥控器通道按键说明，详细说
明在说明书的1-3页，请在电调开关打开前将3-6通道的舵机线做好标记并从接收机上拔掉！
NOTE:Before setting,please double confirm the receiver’s connection,Servos’
positions and Transmitter’s Channel key on Page 1 to Page 3. Please mark the
channel 3 to Channel 6 servo lines(Total 4pcs) before the ESC turns on and unplug
it from the receiver.
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
[单边舵量]
四通：100% 20%
五通：100% 100%
六通：100% 100%
20%
（1）.按“Dec（-）”或“Inc（+）”选择“四通”选项标题下的数值，按“Enter”按键选择此选项下的任意
数值数字闪动，按“Dec（-）”减小百分比数值（数值至少调整到20%），按“Enter”键确认，重复上述操作
将“四通”数值更改为20%或更小；
press “Dec(+)”or “Dec(-)” to select the percent in the “CH4”, press “Enter”, the percent flash,
press“Dec(+)”or “Dec(-)” to make it to be both “20%”;
（2）.将换挡舵机的插头插回接收机的第四通道，请注意正负极，开始调试舵机舵量（请确保车子通电，油门和
转向舵机都有反映），架空车子的四个轮胎；
Plug the 2-speed servo cable into the receiver’s Channel 4. Please notice the place of anode and
cathode, then adjusting the “EPA”(Please make sure the car is power on,throttle servo and steering
servo is active), overhead the 4 wheels to make the wheels off the ground.
（3）.将“四通”选项下左侧的数值加大，留意车架上舵机的动态，加大到如图.1所示状态下红色固定座尽可能
靠近波箱壳体并且舵机没有“滋滋”的响声即可，此时加大油门，看此时的红色固定座有没有位置变化，如没有
按遥控器上的“SWA”按键，使舵机变换到相反方向，车架上舵机臂位置如图.2所示，调整“四通”选项下右侧
的数值，同时加大车子油门，使其增大到舵机没有响声即可，之后检查换挡功能是否正常.
Increase the left percent gradually in the CH4 option, pay attention to the state of the 2-speed servo
increase to be shown as “Chart 1”,the red mount is as close as possible to the gearbox and the servo
has no “Zizizi” sound. Then pull the throttle trigger, if the red mount’s position has no change, enter the “SWA” button of THT6 to
shift the servo direction, the position of the servo arm is shown as “Chart 2”, increase the right percent gradually in the CH4 option
then pull throttle trigger a little.Repeat the step till the servo has no “Zizizi” sound. Finally check the 2-speed shifting function.
图.1 低速档舵机状态
Chart.1 low speed servo state
图.2 高速档舵机状态
Chart.2 high speed servo state
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
M:MODEL1
8.1V
TH T6
ST
TH
0
0
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
CH1:
CH2:
CH3:
CH4:
CH5:
CH6:
0
0
-100
-100
-100
-100
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
[AUX-CH]
CH3：VR
CH4：LK-A
CH5：SwC CH6：SwB
LK-A
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
1.LANGUAGE
2.MODEL
4.STEXP
3.EPA
（2）.Press “Exit”, they are as shown in figure step by step after you set. Press both “Exit” and “Enter” key to enter the main
menu, press “Dec(+)”or “Dec(-)” to select the “16.AUX-CH” option, press “Enter” key to enter the sub-menu,press “Dec(+)”
or “Dec(-)” to select the “CH4”,press “Enter”, the words flash,press “Dec(+)”or “Dec(-)” to select the “LK-A”,press enter
to confirm”CH4:LK-A”. Press “Dec(+)”or “Dec(-)” to select CH5 and CH6 and adjust them to be ”CH5:Swc” and “CH6:SwB”
Press “Exit” to return to the main menu.Press “Dec(+)”or “Dec(-)” to select the “3.EPA” option,then Enter the sub menu.
P r e s s b o t h
2.4GHz FHSS
6-Channel Radio Control System
[EPA]
CH4：100% 20%
CH5：100% 100%
CH6：100% 100%
20%
2
