background image

2) INSTALLATION

Before installing the tralift® make the following

checks:

2.1. Check that the hoist is in good condition.

2.2. Check that the correct capacity hoist 

is to be used.

2.3. When using a hoist with 2 or more falls 

of load chain ensure that there is no 

twisting.

2.4. Check that the load chain is correctly fit-

ted with the link welds on the outside of

the load sheave especially when lifts

other than the standard 3 metres are

used.

2.5. Check that the anchor point is suffi

cient to take the intended load. 

Once these checks have been carried out and

the hoist is installed on its anchor point the

following procedure should be carried out

before any work commences :

2.6. Check that the hoist is correctly 

attached to the anchor point and the top 

hook safety catch is closed.

2.7. Check that the load chain has not 

become twisted during installation.

2.8. Without load check that the up and 

down functions operate correctly.

2.9. When using the hoist with a push 

suspension trolley, without load, check 

that the trolley moves freely. If using a 

geared suspension trolley, without load, 

check the direction of movement by 

pulling on the trolley hand chain.

The user should check that :

The hooks and catches are in good 

condition.

The anchoring accessory of the load

seats fully in the hook and does not 

prevent the catch from closing 

(see illustration).

The load on the hoist is free to align 

itself with the machine's anchor 

point.

3) OPERATION

The tralift® chain hoist is operated by means

of a hand chain which is pulled by the 

operator to lift or lower a suspended load.
With the handwheel casing facing towards the 

operator the following procedure actions lifting

and lowering:
3.1. To lift pull the right hand chain.

3.2. To lower pull the left hand chain.
It is not recommended to pull the hand chain

at excessive speed as this will lead to an

uneven movement of the load. It is recom-

mended to pull the hand chain in a steady

movement to prevent any unnecessary jerking

of the load.

9

WARNING

Содержание tralift 19709

































Отзывы: