background image

BCS 100cm Rotary Mower Attachment

TWT/100RM/0617

 

Page 7

Operation

The adjustment described and the position of the front wheels [A] on the forks [C] (fig.4/4) allow 

the following cutting heights to be obtained:

•  From 5cm to 8cm
•  From 7.5cm to 10.5cm
•  From 10cm to 13cm

Mowing wet grass is not recommended as it may clog the 

discharge chute and make collection difficult.

Best results are obtained with the engine at a high throttle 
setting.

Forward motion speed should be selected according to the grass 
conditions.

Use speed two for light conditions and speed one for difficult 

conditions.

Never allow the engine to labour.

The mower has a built-in blade brake which stops the blade if 
the drive is disconnected.

NEVER ENGAGE THE MOWER IN LONG, UNCUT GRASS.

Using the mower with the collection bag

When using the mower deck with the collection bag, the bag is 

full when the grass exits from the right conveyor hole (fig.4/6).

To empty the bag, it is necessary to point the wheels to the 

inside (fig.4/7).

Unhook the elastic handle (fig.4/8).

Tip the bag up and open it (fig.4/9).

To return to work, open the door [A] with the aim of hooking 

on (fig.4/10).

Fig 4/6

Fig 4/7

Fig 4/8

Fig 4/9

Fig 4/10

Содержание BCS 100cm













Отзывы: