TPS 901-C Скачать руководство пользователя страница 20

Страница: 20 / 31

Page 19

6.6 Data Format

Data is returned to the RS232 port by the

901-C

in the following

format when requested by a PC with the ?D command (section 6.5):

CCCCCCUUU

TTTTTToC

<cr>

or B.

Data is sent to the RS232 port by the

901-C

in the following format

when it is sent by the

901-C

using the Send function (section 6.2):

CCCCCCUUU

TTTTTToC

<cr><lf>

where:

CCCCCC

is the Conductivity or TDS data. maximum 6 characters,
right justified. A “

∗∗

” is sent instead of the decimal point

if the reading is not calibrated.

UUU

is the unit description, left justified. Either “

”, “

”,

“

ppM

” or “

ppK

”. (“

”

is one space.)

is one space.

TTTTTT

is the Temperature data. Maximum 6 characters, right
justified. A “

∗∗

” is sent instead of the decimal point if the

reading is not calibrated.

is the Temperature unit description, left justified. (“

”

one space.)

Notes:

+OVR

–OVR

is sent when the Data is over-range.

BUSY

<cr> is sent when the

901-C

is Busy (ie in calibration, Baud Rate mode,

Send Rate mode etc.) or when data is not available.

Содержание 901-C
































Результаты поиска

Содержание 901-C

Отзывы:

TPS 901-C, Руководство пользователя, Страница: 20 / 31

Результаты поиска

Содержание 901-C

Отзывы: