TPS 901-C Скачать руководство пользователя страница 2

Страница: 2 / 31

Page 1

Contents

Introduction .............................................................................................. 2

1.1

901-C Display and Controls .............................................................................. 2

1.2

901-C Rear Panel Connectors ............................................................................ 2

1.3

901-C Front Panel ............................................................................................. 3

1.4

Unpacking Information ..................................................................................... 4

1.5

Specifications.................................................................................................... 5

Operating Modes...................................................................................... 8

Conductivity Calibration .......................................................................... 9

3.1

Calibration Procedure........................................................................................ 9

3.2

Calibration Notes ............................................................................................ 10

3.3

Calibration Messages ...................................................................................... 11

TDS Calibration ...................................................................................... 12

4.1

Calibration Procedure...................................................................................... 12

4.2

Calibration Notes ............................................................................................ 13

4.3

Calibration Messages ...................................................................................... 14

Temperature Calibration ........................................................................ 15

5.1

Calibration Procedure...................................................................................... 15

5.2

Calibration Notes ............................................................................................ 15

5.3

Calibration Messages ...................................................................................... 16

RS232 Port.............................................................................................. 17

6.1

Setting the Baud Rate...................................................................................... 17

6.2

Sending Readings to the RS232 Port................................................................ 17

6.3

RS232 Configuration ...................................................................................... 18

6.4

Communication and Statistical Software.......................................................... 18

6.5

Commands...................................................................................................... 18

Recorder Output Option ........................................................................ 20

7.1

RS232 / Recorder Output Socket Connections ................................................. 21

Selecting k=10 or k=0.1 Sensors ........................................................... 22

Initialising the 901-C .............................................................................. 23

10.

Troubleshooting ................................................................................. 24

10.1

General Error Messages .............................................................................. 24

10.2

Conductivity and TDS Troubleshooting....................................................... 25

10.3

Temperature Troubleshooting...................................................................... 26

11.

Appendices......................................................................................... 27

11.1

Care, Cleaning and Maintenance of Conductivity Sensors............................ 27

11.2

Replatinising Conductivity Sensors ............................................................. 28

12.

Warranty ............................................................................................. 29

Содержание 901-C
































Результаты поиска

Содержание 901-C

Отзывы:

TPS 901-C, Руководство пользователя, Страница: 2 / 31

Результаты поиска

Содержание 901-C

Отзывы: