Toyotomi MUL12- FWCA Скачать руководство пользователя страница 24

Страница: 24 / 49

CONTROL

them is pressed continuously, the set time will increase/ decrease by 0.5hr every 0.5s.

Swing Setting

Swing On: Press Function under on state of the unit to activate the swing function. In this case,

will blink.

$IWHUWKDWSUHVV(QWHUFDQFHOWRPDNHDFRQ¿UPDWLRQ

Swing Off: When the Swing function is on, press Function to enter the Swing setting interface, with

blinking.

After that, press Enter/cancel to cancel this function.

Note:
m. Sleep, Save, Turbo, Blow or Quiet setting is the same as the Swing setting.

n. After the setting has been done, it has to press the key “Enter/cancel” to back to the setting status or quit

DXWRPDWLFDOO\¿YHVHFRQGVODWHU

Sleep Setting

6OHHSRQ3UHVV)XQFWLRQXQGHURQVWDWHRIWKHXQLWWLOOWKHXQLWHQWHUVWKH6OHHSVHWWLQJLQWHUIDFH7KHQSUHVVŸRU

źWRVZLWFKDPRQJ6OHHS6OHHSDQG6OHHS$IWHUWKDWSUHVV(QWHUFDQFHOWRFRQ¿UPWKHVHWWLQJ

Sleep off: When the Sleep function is activated, press Function to enter the Sleep setting interface. After that, press

Enter/cancel to can this function.

Sleep off is default after power failure and then power recovery, and the sleep functions is unavailable under the

fan mode.

There are three Sleep modes: Sleep 1, Sleep 2 and Sleep 3.
1) Sleep 1
In the Cooling or Dry mode, the temperature will increase by 1

after the unit runs under Sleep 1 for 1hr and 1

after another 1hr.After that, the unit will run at this temperature.

In the Heating mode, the temperature will decrease by 1

after the unit runs under Sleep 1 for 1hr and 1

after

another 1hr. After that, the unit will run at this temperature.

1) Sleep 2
In the Cooling mode, the temperature may be set between 16

-23

, 24

- 27

or 28

- 29

or at 30

(Note: The curve is only for reference, the actual temperature is subject to the time point.).

For example: The temperature in the Cooling mode is set at 25

. Under the mode of Sleep 2, the temperature

will increase by 1

every 1hr. After it increases by 2

in total, it will keep at 27

. 7 hours later, it will decrease

by1

, i.e. 26

.After that, the unit will keep running at 26

In the Heating mode, the temperature may be set at 16

or between 17

- 20

, 21

-27

or 28

- 30

For example, the temperature in the Heating mode is set at 22

.Under the mode of Sleep2, the temperature will

decrease by 1

every 1hr. After it decreases by 2

in total, i.e. 20

,the unit will keep running at 20

1) Sleep 3
Sleep curve setting under Sleep 3(DIY mode)
Under the mode of Sleep 3, press Timer to enter the Sleep setting. In this case, “1 HOUR” is displayed where the

timing value once is displayed and the corresponding temperature with the last Sleep curve setting is displayed where
the ambient/preset temperature once in displayed.

3UHVVŸRUźWRFKDQJHWKHFRUUHVSRQGLQJWHPSHUDWXUHVHWWLQJ

Press Timer, time will automatically increase by 1hr, and the corresponding temperature with the last Sleep curve

setting is displayed where the ambient/preset temperature once is displayed.

5HSHDWVWHSDQGV2856OHHSVHWWLQJLV¿QLVKHG
3UHVV(QWHUFDQFHOWRFRQ¿UPWKHVHWWLQJ

Notes:
a. During the above setting, if Function is pressed down or there is not any operation within 5s, sleep curve

setting will be canceled.

b. 26

is the default Sleep curve temperature before delivery. The wired controller will automatically memorize

the Sleep curve after the setting.

Turbo Setting

Turbo function: The unit at the high fan speed can realize quick cooling or heating so that the room temperature

can quickly approach the setting value.