Toyota PZQ90-89011 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 68

background image

Page of 2/68

Introduction

Important Notice

This manual has been designed for technicians who are qualified and educated in the proper procedures of vehicle
safety, handling and maintenance; experienced in installation of navigation systems or who are cable to carry out
installation procedures when given instructions by an experienced technician in a supervisory capacity.

1.

If a problem is found with the rear camera due to installation, refer back to the manual to correct the

problem (s).

2.

Vehicle and rear camera kit components as well as installation procedures are subject to change without prior
notice. Refer to the latest installation manual and service information. Any changes affecting the above items will
be given in the form of “Installation instructions for the system (supplement)” (issued by Fujitsu Ten) or a Service
Bulletin (issued by Toyota).

Definition of Term
WARNING!

Describes precautions that should be observed in order to prevent injury or death to the user during installation

CAUTION!

Describes precautions that should be observed in order to prevent damage to the vehicle or its components, which
may occur during installation of insufficient care is taken

NOTE

Provides additional information that facilitates installation work.

FRONT, REAR, LEFT, RIGHT

Shows the direction when viewed from the driver’s seat.

IMPORTANT

Describes the procedure that must be strictly followed to ensure correct operation of the system, durability and
safety to the end user.

IMPORTANT SAFETY PRECAUTIONS AND PROCEDURES FOR INSTALLER

The following precautions and procedures must be carried out when installing the system to ensure long term
durability, correct operation and safety for the end user.



All wiring must be positioned where it will not interfere with the vehicle operation or systems.



All wiring must be firmly secured using cable ties (supplied).



Cable ties must be positioned at 300mm intervals maximum.



Wiring must not be attached to moving components or position over sharp edges or vehicle components
that may wear and jam or damage wiring.



Excess wiring from antenna and main wiring harness must be bundled at a safe location to ensure no
interference with vehicle operation / systems.



All nuts, bolts and screws removed to carry out the installation of the system must be re-installed to original
vehicle specification and torque values as specified in the applicable Toyota Repair Manual.

© FUJITSU TEN AUSTRALIA PTY LTD

89 COOK STREET, PORT MELBOURNE 3207, VIC

All rights reserved. This book may not be reproduced or copied, in whole or in part, with the written permission of the publisher.

A.C.N. 63 007 413 578

«
1
2
3
4
...
»

Содержание PZQ90-89011





































































Отзывы:

Нет отзывов

Похожие инструкции для PZQ90-89011

SMARTCAM SNH-V6414BN

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 96

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: YI Страницы: 9

Бренд: Tamron Страницы: 9

Бренд: Olympus Страницы: 4

Бренд: Olympus Страницы: 101

Бренд: Olympus Страницы: 121

Бренд: Olympus Страницы: 82

Бренд: Olympus Страницы: 73

Бренд: Olympus Страницы: 70

Бренд: Olympus Страницы: 78

Бренд: Olympus Страницы: 80

Stylus TG-Tracker

Бренд: Olympus Страницы: 79

Бренд: Olympus Страницы: 74

Бренд: Olympus Страницы: 74

Бренд: Olympus Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды