background image

TOYOTA 

MY22 TUNDRA 

2022 -  

DASHCAM 

(Digital Video Recorder) 

Procedure 

 

Page 10 of 14 pages 

Issue: B  11/19/2021 

 

 

 

9.  Route / Bundle Wire Harness 

(a) Before proceeding with securing the 

harness, confirm the connectors have 
been protected with the provided foam 
tape. Use the provided foam tape to 
minimize any potential rattle concerns. 
(Fig. 9-1) 

(b) Secure the Dashcam Pigtail harnesses 

against the existing harnesses on the 
driver’s side of the map light / sunglasses 
pocket opening. Loop and bundle them 
as required. Arrange this in a way that 
does not obstruct the console being 
reinstalled. Tighten the zip tie and snip 
off the excess, and then 

orient the zip 

tie to have the block in the upright 
position to prevent noises from 
contact with the overhead console.

 

(Fig. 9-2) 

(c) Ensure that the connection for the 

console is still free to be connected and 
that the bundled harnesses are not 
obstructing the console map light 
connector. (Fig. 9-3) 

(d) 

Note: Take care not to cause bulging 
in the headliner. Some adjustments to 
the bundle may be required to avoid 
bulging the headliner. 

 

(e) 

Note: Do not block access to the clip 
holes in the body structure or the roof 
console may not fit properly. 

 

  

Fig. 9-1 

Fig. 9-2 

Fig. 9-3 

Содержание PT949-34220















Отзывы: