Toyota 1ZZ-FTE Скачать руководство пользователя страница 50

Страница: 50 / 64

5. INSTALL OIL PRESSURE SWITCH.

(a) Install the oil pressure switch into the adapter using

Loctite 243. Use SST 09816-30010

: Pressure switch

Torque: 13 Nm

(b) Connect the oil pressure switch connector to the

pressure switch.
NOTICE: Turn oil filter until the o-rings touches the

flange. Turn oil-filter 270

by hand.

6. INSTALL INTERCOOLER.

(a) Position the intercooler assembly underneath the

gearbox.

: intercooler (7-1)

(b) Install the bolt M8 x 12 into the gearbox side to fix the

bracket. (hand tighten)

: Bolt (7-6)

bracket (hand tighten)

: Bolt (7-8)

7. INSTALL INTERCOOLER INLET PIPE.

(a) Position intercooler inlet pipe, 2 hoses and 4 hose

clamps.

: intercooler inlet pipe (6-1)

: Hose turbo side (6-2)

: Hose intercooler side (6-3)

: Clamp (4 pcs.) (6-4)

(b) Tighten outer hose clamps on turbo charger side and

intercooler side.
Torque: 3 Nm

hand tighten inner clamps.

(d) Install the inlet pipe with a bolt to the engine.

: Bolt (6-5)

Torque: 12 Nm

(e) Tighten the inner hose clamps.

Torque: 3 Nm

45˚

Содержание 1ZZ-FTE

































































Результаты поиска

Содержание 1ZZ-FTE

Отзывы:

Бренды по названию

Популярные бренды

Toyota 1ZZ-FTE, Руководство по установке

Результаты поиска

Содержание 1ZZ-FTE

Отзывы:

Бренды по названию

Популярные бренды