Toyota 1ZZ-FTE Скачать руководство пользователя страница 47

Страница: 47 / 64

5. INSTALL TURBO CHARGER BRACKET.

(a) Install the bracket with short bolt and washer to the

engine (hand tighten).

: Bolt (5-4)

: Washer (5-5)

: Bracket (5-2)

(b) Install the bracket with long bolt, washer and spacer to

the Turbo charger (hand tighten).

: Bolt (5-3)

: Washer (5-5)

: Bush (5-6)

6. TIGHTENING TURBO CHARGER.

(a) Tighten the 4 bolts of the Turbo charger.

Torque: 28 Nm

(b) Bend the locking plates against the side of the bolt.
(c) Tighten the bolt of the bracket to the Turbo charger.

Torque: 20 Nm

(d) Tighten the bolt of the bracket to the engine.

Torque: 16 Nm

7. INSTALL WATER INLET CONNECTION.

(a) Remove the water hose clamps.

: Hose clamps (2 pcs.)

(b) Remove the water hose.

: Water hose.

NOTICE: Some coolant will flow out of the cooling

system.

: Hose Heat Protection. (17-7)

(d) Install hose on turbo inlet side with a clamp.

: Clamp

Torque: 3 Nm

(e) Install heat protective hose with Lockwire. Use a

stainless steel wire to fit.

: Hose. (16-3)

NOTICE: Ensure that the clamp is covered by the

sleeve.

Содержание 1ZZ-FTE

































































Результаты поиска

Содержание 1ZZ-FTE

Отзывы:

Бренды по названию

Популярные бренды

Toyota 1ZZ-FTE, Руководство по установке

Результаты поиска

Содержание 1ZZ-FTE

Отзывы:

Бренды по названию

Популярные бренды