manualshive.com logo in svg

Toyota 1ZZ-FTE, Руководство по установке

Поделиться
Скачать
Toyota 1ZZ-FTE Скачать руководство пользователя страница 43

43

13. Turbo preparation

1. TURBO PROTECTION.

CAUTION: Cover all the inlet and outlet holes with 

protective tape to avoid parts from 
falling in.

2. REMOVE PLATE WITH PRESSURE ACTUATOR.

(a) Remove the pressure actuator bracket by removing 

the clip and 2 bolts.

R

: Clip

R

: Bolt (2 pcs.)

R

: Pressure actuator.

K

: Turbo charger (3-1)

CAUTION: Do not damage nut assurance.

3. TURBO LUBRICATION.

(a) Insert some engine oil into the oil return outlet side of 

the turbo and rotate the turbo turbine axle a few times 
to lubricate the axle bearings.

CAUTION: Close the inlet hole with tape to avoid 

parts from falling in.

 

4. INSTALL WATER ADAPTERS.

(a) Install the water outlet (2) adapter (16/16mm).

K

: Outlet adapter No.1 (17-4)

Torque: 70 Nm

NOTICE: The boss-side of the adapter is facing the 

turbo housing side.

(b) Install the water inlet adapter (14/16mm).

K

: Inlet adapter No. 2 (16-2)

Torque: 50 Nm

R

R

R

R

K

K

K

1

2

Содержание 1ZZ-FTE

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды