Town & Country Fireplaces TC36 Скачать руководство пользователя | Manualshive

Страница: 1 / 52

background image

SERIAL #

Visit

www. townandcountryfi replaces.net

for the most up-to-date version of this manual

TC36 & TC36 ARCH
INSTALLATION
AND OPERATING
INSTRUCTIONS

101215-52 TC36_D & TC36_DAR 5056.427D

MODEL: TC36 & TC36AR

SERIES D

MODULAR DIRECT VENT

FIREPLACE

WARNING: If the information in these
instructions is not followed exactly, a fi re or
explosion may result causing property damage,
personal injury or death.

FOR YOUR SAFETY

Installation and service must be performed
by a qualifi ed installer, service agency or the
gas supplier.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch.
• Do not use any phone in your building.
•  Immediately call your gas supplier from

a neighbour’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier call

the fi re department.

Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.

This appliance may be installed in an aftermarket
permanently located, manufactured home (USA only)
or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certifi ed kit is used.

This appliance is suitable for installation in a
bedroom or bed sitting room.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

1
2
3
...
»

Содержание TC36





















































Отзывы:

Нет отзывов

Похожие инструкции для TC36

Бренд: Riello Страницы: 8

Бренд: Riello Страницы: 56

Бренд: Riello Страницы: 56

MICROFLAME burner MFB/E

Бренд: Proxxon Страницы: 30

Бренд: Cal Flame Страницы: 28

Бренд: Varmebaronen Страницы: 24

BGN 40 DSPGN-ME

Бренд: baltur Страницы: 72

Бренд: Unigas Страницы: 116

GI MIST 1000 DSPGM

Бренд: baltur Страницы: 88

Speedflame Power Gas Burner

Бренд: Adams Страницы: 2

Бренд: Adams Страницы: 19

KOB PYROMAT DYN 45

Бренд: Viessmann Страницы: 44

Nutrichef PKST11

Бренд: Pyle Страницы: 6

eurofire XL-GRYM

Бренд: Ekosystem AB Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды