Town & Country Fireplaces TC36 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 52

background image

The Town & Country Fireplace installation and venting must conform to the current CAN/CGA-B149 installation code (in
Canada) or the current National Fuel Gas Code, ANSI Z223.1 (in the USA), and approved per local codes. Only qualified
(licensed or trained) personnel should install this product.

In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install this product.

In some jurisdictions, the Town & Country Fireplace may be installed in Manufactured Homes after the "first sale". Consult
local codes for approval. The fireplace must be fastened in place.

Install in accordance with the current standard Mobile Homes, CAN/CSA Z240 MH (in CANADA), and the Manufacturer's
Home Construction and Safety Standard, Title 24 CFR, Part 3280 or the current Standard for Fire Safety Criteria for
Manufactured Home Installations, Sites and Communities ANSI/NFPA 501A (in the USA).

Warning: Turn off the fireplace, and allow ample time for the unit to cool before proceeding.

Caution: The ceramic glass is very fragile, and should be handled with care.

The glass door frame is held in place by two spring-loaded latches that are operated by a one-piece latch handle.

1. Remove safety barrier screen (Figure 5) by prying the top portion of the screen toward you, then lift the screen from

its tabs (inset) located at the base of the window frame.

2. Remove the TC Finishing Touch Trim Kit from the glass door frame. (If installed)

3. Using a screwdriver (Figure 6) or other similar object, push against the notch in the top of the latch and grab the bot-

tom of the latch handle as it protrudes (Figure 7). Lift handle until latch hook disengages. Repeat for other side while
holding glass door so that it does not tip out.

4. Tilt the top of the glass door frame out to clear the top edge of the unit. Grasp the sides of the frame and lift up and

out to disengage from its bottom track.

5. Place the glass door frame in a safe place to avoid damage.

6. Reassemble in reverse order. Latch handle should snap into place and be flush with glass door frame when engaged

correctly.

7. Reinstall trim kit if required.

8. Reinstall safety barrier screen.

TIP:

To ensure glass door is
properly latched, grasp the
top left and right sides of the
glass frame. Under moderate
pressure it should pull forward
and return to original position
evenly on both sides.

Figure 5: Safety barrier screen. Figure 6: Accessing handle.

HANDLE

Figure 7: Handle.

7

5056.427D

TC36_D & TC36_DAR_101215-52

Installation Requirements

Manufactured (Mobile) Home

Door Frame Removal

«
...
5
6
7
8
9
...
»

Содержание TC36





















































Отзывы:

Нет отзывов

Похожие инструкции для TC36

Бренд: Unigas Страницы: 84

Бренд: Rasmussen Страницы: 18

Бренд: Comtherm Страницы: 25

Slimline SB1100C

Бренд: ICON FIRES Страницы: 13

Бренд: DS Produkte Страницы: 40

Бренд: BUG-O Страницы: 38

Бренд: Ecosmar+ Страницы: 7

Бренд: LAMBORGHINI Страницы: 112

Multicalor 500.1 PR

Бренд: Ecoflam Страницы: 36

Бренд: Vermont Castings Страницы: 30

Бренд: Riello Страницы: 48

Бренд: AEG Страницы: 24

OPT-TT M Series

Бренд: Outdoor Plus Страницы: 11

Бренд: T&C Страницы: 8

Бренд: Weber Страницы: 12

Бренд: Sovelor Страницы: 16

Heatranger 880K

Бренд: Rayburn Страницы: 33

Бренд: krom schroeder Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды