manualshive.com logo in svg

Town & Country Fireplaces TC36 SEE-THRUC SERIES, Инструкция по установке и эксплуатации


Поделиться
Скачать
background image

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this label.
2. Set wall switch/ hand held remote to lowest setting.
3. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot by
hand.

4. Push the "On/ Off" switch to the fireplace Off.
5. Allow sufficient length of time (minimum 5 minutes) for any

gas in the combustion chamber to escape. If you still smell
gas, STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.

WARNING: If you do not follow these instructions

exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.

A. This appliance is equipped with an ignition device which auto-

matically lights the pilot. Do not try to light the pilot by hand.

B. BEFORE LIGHTING smell all around the appliance area for gas.

Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
- Do not try to light any appliance.

FOR YOUR SAFETY READ BEFORE LIGHTING

6. Push the "On/ Off" switch to turn the fireplace on.

- If the burner does not light, repeat steps 4 through 6.
- If the burner will not light or stay lit after several
tries,push the "On/ Off" switch to the fireplace off and
call your service technician or gas supplier.
Note: Sufficient time must be allowed for air to escape
from lines if the unit is being lit for the first time.

7. Set fireplace to desired setting by using either the wall

switch or hand held remote.

- Do not touch any electric switch; do not use any phone in your
building.
- Immediately call your gas supplier from a neighbour's phone.
Follow the gas supplier's instructions.
- If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never

use tools. If the knob will not push in or turn by hand, don't try
to repair it, call a qualified service technician. Force or at-
tempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the
appliance & to replace any part of the control system & any gas
control which has been under water.

310106

5051.173

5-TC30

         Hot while in operation. Do not touch. Severe burns may result. Keep children, clothing,

furniture, gasoline and other liquids having flammable vapours away. Keep burner and control compartment
clean. See installation and operating instructions accompanying the appliance.

CAUTION

:

   L'appareil est chaud lorsqu'il fonctionne. Ne pas toucher l'appareil. Risque de

brûlures graves. Serveiller les enfants. Garder les vêtements, le meubles, l'essence ou autres liquides
produisant des vapeurs inflammables loin de l'appareil. S'assurer que le brûleur et le compartiment des
commandes sont propres. Voir les instructions d'installation et d'utilisation qui accompagnent l'appareil.

ATTENTION

:

TO TURN OFF GAS TO APPLIANCE

1. Set wall switch / hand held remote to lowest setting.
2. Push the "on/ off" switch to the "Off" position.

3. Turn off all electric power to the appliance and remove

backup batteries if service is to be performed or for extended
shutdown.

Due to high surface temperatures, keep children, clothing and furniture away. Keep burner and control compartment
clean. See installation and operating instructions accompanying the appliance.
A cause de la temperature elevee des parios, tenir eloignes les enfants, les vetements et les meubles. Maintenir propres le
bruleur et le compartiment de commande. Voir les instructions relatives a l'installation et au fonctionnement qui accompagnent
l'appareil.

When lit for the fi rst time, the fi replace will emit a slight odour for a couple of hours. This is 
due to the curing of paints, sealants and lubricants used in the manufacturing process. This 
condition is temporary. Open doors and windows to ventilate area. Odour caused by the 
curing process may cause discomfort to some individuals.

It is normal for fi replaces fabricated of steel to give off some expansion and/or contraction 
noises during the start up or cool down cycle. Similar noises are found with your furnace 
heat exchanger or cook stove oven.

28

TC36_CSTE 071010-44

Lighting Instructions

First Fire

Содержание TC36 SEE-THRUC SERIES













































Отзывы:

Нет отзывов

Похожие инструкции для TC36 SEE-THRUC SERIES

L'Artistico APOLLO 15 Installation, Use And Maintenance Manual preview
APOLLO 15
Бренд: L'Artistico Страницы: 48
Jensen La Valle RF-1591LP Owner'S Manual preview
La Valle RF-1591LP
Бренд: Jensen Страницы: 51
Majestic RUBY30IN Installation Instructions preview
RUBY30IN
Бренд: Majestic Страницы: 3
Jeco Windsor FP006 Quick Start Manual preview
Windsor FP006
Бренд: Jeco Страницы: 3
C3 C3P23C9-2067W Operating Instructions preview
C3P23C9-2067W
Бренд: C3 Страницы: 2
Evonic Fires Avesta Instruction Manual preview
Avesta
Бренд: Evonic Fires Страницы: 44
Kingsman CR97-003 Owner'S Operation And Installation Manual preview
CR97-003
Бренд: Kingsman Страницы: 17
Majectic BFC36 Owners Installation And Operating Manual preview
BFC36
Бренд: Majectic Страницы: 24
Twin-Star International ChimneyFree 25MM5326 Manual preview
ChimneyFree 25MM5326
Бренд: Twin-Star International Страницы: 24
Woodard Direct WDC-SEA-FP-TOP Assembly Instructions preview
Direct WDC-SEA-FP-TOP
Бренд: Woodard Страницы: 2
EdilKamin 809490 Installation, Use And Maintenance Manual preview
809490
Бренд: EdilKamin Страницы: 16
Majestic WMII-42AD Installation Manual preview
WMII-42AD
Бренд: Majestic Страницы: 20
Euroheat Nestor Martin 023 Operating Instructions Manual preview
Nestor Martin 023
Бренд: Euroheat Страницы: 32
Astria Fireplaces 900005-07 Installation Instructions preview
900005-07
Бренд: Astria Fireplaces Страницы: 2
Landmann Hartford 25805 Assembly And Use Instructions preview
Hartford 25805
Бренд: Landmann Страницы: 8
FireplaceXtrordinair 35 Custom Builder Owner'S Manual preview
35 Custom Builder
Бренд: FireplaceXtrordinair Страницы: 48
RAIS Caro 90 Installation Manual preview
Caro 90
Бренд: RAIS Страницы: 30
Napoleon NEFE29-1415E Installation And Operating Instructions Manual preview
NEFE29-1415E
Бренд: Napoleon Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды