Tower Hobbies Laser 200 Flatty Скачать руководство пользователя страница 8

Страница: 8 / 16

Assemble the Top Half

❏

1. Test fi t the top half of the fuselage to the assembly. If

necessary, use a hobby knife to adjust some of the joining
tabs/notches to get a perfect fi t.

❏

2. Carefully glue the top half of the fuselage into position —

as you proceed, make sure the top remains parallel with the
bottom and perpendicular to the wing.

❏

3. Glue the vertical fuselage post to the bottom the fuselage.

❏

4. Fit, then glue the 1mm carbon fi ber top horizontal stab

braces into position. Same as before, use a builder’s square to
be certain the vertical stab remains vertical and perpendicular
to the horizontal stab.

❏

5. Notch, position, then glue the

round

brace reinforcements

into position.

❏

6. Hinge the bottom of the rudder to the bottom fuselage

half with the piece of hinge tape included with this kit.

Содержание Laser 200 Flatty

















Результаты поиска

Содержание Laser 200 Flatty

Отзывы:

Похожие инструкции для Laser 200 Flatty

Бренды по названию

Популярные бренды

Tower Hobbies Laser 200 Flatty, Инструкция по эксплуатации

Результаты поиска

Содержание Laser 200 Flatty

Отзывы:

Похожие инструкции для Laser 200 Flatty

Бренды по названию

Популярные бренды