background image

 

Other warnings

 

 

Save these instructions 

Attention 

Do not let comfort or familiarity with the product (gained from repeated use) replace strict 

adherence to safety rules for the product in question. Incorrect use or non-compliance 

with the safety rules indicated in this instruction manual can cause serious personal 

injury. 

symbols 

The symbols used for the tool are shown below. 

symbols 

 

volts 

 

DC 

 

no load speed 

 

Revolutions per minute 

 

number of strokes 

 

Important safety instructions for the battery cartridge 

1.  Before using the battery, read all instructions and cautionary markings on: 

a.  The battery charger 

b.  Battery 

c.  Product 

2.  Do not disassemble the battery cartridge. 

3.  If the operating time has been shortened excessively, stop using it immediately. 

It can result in overheating, possible burns, and even an explosion. 

4.  If electrolyte gets into your eyes, flush with clean water and seek immediate 

medical attention. It can result in loss of sight. 

5.  Do not short circuit the battery cartridge: 

a.  Do not touch the terminals with any conductive material 

b.  Avoid storing the battery cartridge in a container with other metallic 

objects such as nails, coins, etc. 

c.  Do not expose the battery cartridge to water or rain. 

Note: A short circuit in the battery can cause a large current flow, 

overheating, possible burns and even a breakdown. 

6.  Do not store the tool or battery cartridge where the temperature may reach or 

exceed 50°C (122°F). 

7.  Do not incinerate the battery cartridge even if it is badly damaged or completely 

spent. The battery cartridge may explode in case of fire. 

8.  Be careful not to drop or hit the battery. 

9.  Do not use a damaged battery. 

10. Lithium-ion batteries are subject to the requirements of the dangerous goods 

legislation. 

11. Follow local regulations regarding battery disposal. 

Содержание TIRLI2002


















Отзывы: