background image

SONAR SETTING

8

In most time the default setting is enough. However in some situation, to get a better using, you need adjusting 

the menu setting.

Determines how echoes will be displayed on the screen. Increasing the sensitivity will make you see more 
details on the screen. In deep water, increasing the sensitivity. whereas in shallow decreasing the sensitivity.

1) Sensivity

Fish ID. Sens. adjust the threshold of fish size display
Selecting a higher setting allows weak returns being displayed as fish, which is helpful especially when you 
are intending to find smaller fish species or bait fish.
Selecting a low setting will prevent weak sonar returns being displayed as fish, which will be very helpful 
when you are seeking large species of fish.

2) Fish ID. Sens.

The gain controls the sensitivity of the hardware receiver. A 
higher gain makes the sonar more sensitive to echo returns, 
allowing it to display weaker targets. If the gain is set too 
high, the image might be cluttered with background noise.

Note: 

when set in [shallow water mode], the [Gain] option 

will be disable.

3) Gain

Used to get a better sonar performance in shallow water.

4) Shallow Mode

[gain] automatilly  

changed to high 

sensivity 

Gain=4x

[Gain]=2x

Содержание TF300













Отзывы: